ödalg äbäi What is the the transfer function of the first-order system which has the impulse response curve as in * ?the following figure Impulse Response 1.8 1.6 1.4 1.2 System: sys Time (seconds): 0.333 Amplitude: 0.737 0.8 Slop 0.6 0.4 0.2 0.2 0.4 0.6 0.8 1.2 1.4 1.6 1.8 2 Time (seconds) 1/(s+3) O 2/(s+3) O 6/(s+3) O No one of the answers in a, b, and c Amplitude

ödalg äbäi What is the the transfer function of the first-order system which has the impulse response curve as in * ?the following figure Impulse Response 1.8 1.6 1.4 1.2 System: sys Time (seconds): 0.333 Amplitude: 0.737 0.8 Slop 0.6 0.4 0.2 0.2 0.4 0.6 0.8 1.2 1.4 1.6 1.8 2 Time (seconds) 1/(s+3) O 2/(s+3) O 6/(s+3) O No one of the answers in a, b, and c Amplitude

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.6P

See similar textbooks

Similar questions

Sketch the level response for a bathtub with cross-sectional area of 8 ft 2 as a function of time for the following sequence of events; assume an initial level of 0.5 ft with the drain open. The inflow and outflow are initially equal to2ft3/min.(a)The drain is suddenly closed, and the inflow remains con-stant for 3 min (0≤t≤3).(b)The drain is opened for 15 min; assume a time constant in a linear transfer function of 3 min, so a steady state is essentially reached (3≤t≤18) (c)The inflow rate is doubled for 6 min (18≤t≤24).(d)The inflow rate is returned to its original value for 16 min(24≤t≤40).
Figure 1 shows an electrical system comprising a series RLC circuit and input voltagesource ein(t).(a) Derive the input-output equation with output y = I and input u = ein(t). (b) Using the derived input-output equation, drive the system transfer function G(s)that relates output to input. Use the following numerical values for the electrical systemparameters: resistance R = 2Ω, inductance L = 0.25H, and capacitance C = 0.4F. (c) Using the derived transfer function, derive the time-domain ordinary differentialequation for the input-output equation of this electrical system. (d) Draw the complete block diagram of this series RLC circuit using the derived transferfunction.
1.block diagram physical meaning and the time response for different inputs
In a tank heater with agitator, the relationship between the tank outlet temperature (T) and the heat given to the system by the heater connected to the tank (Q) is expressed by the model equation below. Accordingly, find the gain and time constant of the transfer function between temperature and heat. If the 1000 W heater power is suddenly increased by 25%, in how many minutes will the outlet temperature reach the new steady state value? (Note: The first steady state tank outlet temperature is 65 °C and the unit of time constant is minutes)
a)If the system has a transfer function of the form G_P (s)=H(s)/(V_m (s) )=μ/(1+Ts) where µ is the gain and T is the time constant, calculate values for µ and T for the case where the valve is at position 3. Hints: Use the constants and information in table 1. The dynamics of the water tank can be found by applying the continuity equation: qin - qout = rate of change in water tank
Q.1 - The open loop transfer function for a unity - feedback systemis G(s)= XL‘ 7xs and r(t)=3t determine steady state error.If it is desired to reduce this existing error by 7% fined new value of gain of the system.
root locus electrical engineering Don't overthink and reject. Complete the solution as per the given transfer function. No need of quadratic equation just simplify for the exact given transfer function.
The block diagram given below; A) Reduce it B) G1(s)=2/s ; G2(s)=1/4s+2 ; G3(s)=4 ;H(s)=0.5 Given the values of the system; find the time constant, its natural frequency and damping rate and explain what kind of dynamic behavior it exhibits accordingly. C)Find the poles and zeros of the system according to the values in (B).Is the system stable? Find the unit step response (Inverse Laplace).
A vibrating spring-mass system has the feedback control system shown in Fig Q3 below. (figure attached as image ACT)If K = 12.25 determine:6.1 the transfer function ; (3)6.2 the characteristic equation with a impulse input; (1)6.3 the un-damped natural frequency of the system; (2)6.4 the damping ratio; (2)6.5 the damped natural frequency; (2)6.6 the maximum percentage overshoot; (2)6.7 the peak time; (1)6.8 the settling time for the response within 2%. (2)
Consider the thermocouple properties you found in the question "Temperature of a thermocouple (1/3)" If the thermocouple is initially outside of the bath at room temperature (20 °C), what is the maximum temperature it will register if it's instantaneously inserted into the batch (55 °C) for 18 seconds and then removed? Use an inverse Laplace transform to find the solution. a. 32.68 °C b. 44.97 °C c. 64.97 °C d. 12.68 °C
The transfer function of a system is the ratio between _________________ and ____________ in Laplace transform. a. Output and Input b. Input and Output c. Input and Feedback d. Output and Feedback
Calculating the separation and / or joining angles in the negative feedback control circuit, if any, given as Controlling (K) and Controlled G (s) = (s + 1) / (s2-4 * s + 5) Explanation: The roots of the equation (s2-4 * s + 5); s1 = 2 + 1 * j and s2 = 2-1 * j and the system Transfer Function is TF (s) = K * G (s) / (1 + K * G (s)). a. There are split angles up to (+108.435) and (-108.435) b. There are split angles as much as (+71,565) and (-71,565) c. There are conjunction angles of (+90) and (-90). D. There are separation angles as much as (+18.435) and (-18.435). E. There are no separation and convergence angles.