A system is described by the following differential equation: [Section 2.3] d²x dx di² -+2+3x = 1 dt with the initial conditions x(0) = 1, x(0) = -1. Show a block diagram of the system, giving its transfer function and all pertinent inputs and out- puts. (Hint: the initial conditions will show up as added inputs to an effective system with zero initial conditions.)

A system is described by the following differential equation: [Section 2.3] d²x dx di² -+2+3x = 1 dt with the initial conditions x(0) = 1, x(0) = -1. Show a block diagram of the system, giving its transfer function and all pertinent inputs and out- puts. (Hint: the initial conditions will show up as added inputs to an effective system with zero initial conditions.)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.6P

See similar textbooks

Similar questions

Calculating the separation and / or joining angles in the negative feedback control circuit, if any, given as Controlling (K) and Controlled G (s) = (s + 1) / (s2-4 * s + 5) Explanation: The roots of the equation (s2-4 * s + 5); s1 = 2 + 1 * j and s2 = 2-1 * j and the system Transfer Function is TF (s) = K * G (s) / (1 + K * G (s)). a. There are split angles up to (+108.435) and (-108.435) b. There are split angles as much as (+71,565) and (-71,565) c. There are conjunction angles of (+90) and (-90). D. There are separation angles as much as (+18.435) and (-18.435). E. There are no separation and convergence angles.
Q.1 - The open loop transfer function for a unity - feedback systemis G(s)= XL‘ 7xs and r(t)=3t determine steady state error.If it is desired to reduce this existing error by 7% fined new value of gain of the system.
1. Give an example of open loop and closed loop system (one example each). Also state the input, control system, feedback and output parameter. Example. 1. Open Loop - Water Heater: Input - Water Temperature (Cold) System - Heating Element Output - Water Temperature (Hot) 2. Closed Loop - Air-conditioning System Input - Desired Room Temperature Control - Motor controller/Compressor/ACU Feedback - Temperature Sensing Output - Room Temperature
A stock-flow system models the level of water in a lake. Near a certain equilibrium point, there are three feedback loops: an amplifying feedback loop with strength of +0.55 per month, a stabilizing feedback loop with strength of -0.09 per month, and an amplifying feedback loop with strength of +0.79 per month. Calculate the strength of the overall feedback.
a)is the aircraft stable about the equilibrium represented by the transfer function? b) Using proportional feedback,what is the range of acceptable gains for the closed loop systen to be stable? c) Design a feedback control system that allows the pilot to command a pitch angle with overshoot less than or equal to 4.15% and a natural frequency of greater than or equal to 0.99 rad/s d) Design a feedback control system that allows the pilot to command a pitch angle with the same overshoot and a natural frequency of one half the system in part c.
Example 1.1 Figure 1.5 shows the block diagram of a closed-loop flow control system. Identify the following elements: (a) the sensor, (b) the transducer, (c) the actuator, (d) the transmitter, (e) the controller, (f) the manipulated variable, and (g) the measured variable. In the figure above, the (a) sensor is labeled as the pressure cell. The (b) transducer is labeled as the converter. However, there are two converters: one for converting pressure to current, and another converting current to pressure for operating the actuator. The (c) actuator is labeled as the pneumatic valve. The (d) transmitter is labeled as the line driver. The (e) controller is labeled as the PLC. The (f) manipulated variable is labeled as the pressure developed by the fluid flowing through the orifice plate. The (g) measured variable is the flow rate of the liquid.
Name two effects of negative feedback.
a)If the system has a transfer function of the form G_P (s)=H(s)/(V_m (s) )=μ/(1+Ts) where µ is the gain and T is the time constant, calculate values for µ and T for the case where the valve is at position 3. Hints: Use the constants and information in table 1. The dynamics of the water tank can be found by applying the continuity equation: qin - qout = rate of change in water tank
PLEASE GIVE COMPLETE AND DETAILED SOLUTION The oven shown in Figure 1 has a heating element, qi with capacitances C = 50 J/K. The corresponding temperature is T and ambient temperature is Ta. The thermal resistance of the oven wall is R = 2 K-s/J. The system has a steady-state error in the response, T(t) to a change in the reference input. The steady state error can be reduced if a proportional control action, Kp is included in the controller. Determine the range of values of Kp of the system so that the steady state error is lower than 0.4. (Hint: Kindly determine the steady state error at value 0.4)
Figure 1 shows an electrical system comprising a series RLC circuit and input voltagesource ein(t).(a) Derive the input-output equation with output y = I and input u = ein(t). (b) Using the derived input-output equation, drive the system transfer function G(s)that relates output to input. Use the following numerical values for the electrical systemparameters: resistance R = 2Ω, inductance L = 0.25H, and capacitance C = 0.4F. (c) Using the derived transfer function, derive the time-domain ordinary differentialequation for the input-output equation of this electrical system. (d) Draw the complete block diagram of this series RLC circuit using the derived transferfunction.
The block diagram given below; A) Reduce it B) G1(s)=2/s ; G2(s)=1/4s+2 ; G3(s)=4 ;H(s)=0.5 Given the values of the system; find the time constant, its natural frequency and damping rate and explain what kind of dynamic behavior it exhibits accordingly. C)Find the poles and zeros of the system according to the values in (B).Is the system stable? Find the unit step response (Inverse Laplace).
The steady-state response is the part of the Total Response which does not approach infinity as time approaches infinity. True False