of water is cantrolled by L-shaped gate. 18=1000 K8 lmi) a) Draw FBD wl distributed load due to fresh water channel on the L-shaped gate b) Draw FBD ul equivalent pant load an c) Determine force on to gate due to water. d) Determine load Prequred for gate to reman clo sed. Flow 8m wide gate P 18m 15m Sm

of water is cantrolled by L-shaped gate. 18=1000 K8 lmi) a) Draw FBD wl distributed load due to fresh water channel on the L-shaped gate b) Draw FBD ul equivalent pant load an c) Determine force on to gate due to water. d) Determine load Prequred for gate to reman clo sed. Flow 8m wide gate P 18m 15m Sm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 2.75-m-diamter wood-stave pipe has 9m3/s of water entering through a horizontal 30oreducing bend where the other end is 1.82 m indiameter. The curved portion is made of steel plate toresist rupture and the bend is embedded in concreteblock weighing 2400 kg/m3. The pressure at entranceof the bend is 138 kPa. The combined weight of thebend and its content is 268 kN. Neglecting friction inthe flow, compute the minimum volume of concreteblock holding the bend that can withstand the thrust ofwater on the bend assuming the coefficient of frictionbetween the concrete and its foundation is 0.30.
A- A regulator with discharge = 22m3/sec , rounded entrance is used for piers and abutment , water level at flood time =92.8 , bed level=90.3m at u/s. D/s water level = 92.2m.Bed level under gate: 91m. Decide the flow condition after the gate when it is opened partially (free or submerged), then find the value of partial opening . no of piers=2, each one has thickness =1m . B - For a stiffy clay soil Do you accept depth of flow = 3m with So=0.0007 if the ratio of B/y=3 and the cross section of the canal was rectangle? Why?
Factor of safety,F.S.=2.0
Consider the ¼-circular curved gate hinged below. The gate radius is 3 m,its width (into the page) is 5 m, and its weight is negligible. Obtain the forcemagnitude Q so that the gate remains closed as shown. The specific weight of the water is γw = 9.81 kN/m3. Please show all working and free body diagrams and explain clearly.
Required: average pressure acting on the gate? Fr? Yc? Yr?
distributed load = 13kN L = 3m (3L = 3 x 3m = 9m) F = 7 kN.
he support bracket for a water pipe that brings water from the city water systeminto the basement of DeMoss Hall needs to be replaced since it was originally improperlydesigned. An ENGR 315 class is contracted to determine the proper forces in the x and ydirection on the redesigned support at C. Water from the city line flows into DeMoss Hall in a 2-inch diameter pipe at A at 20 ft/sec and pressure 20 psi. The weight of the piping system andenclosed water is 110 lbf. The specific gravity of the water is 62.4 lbf/ft3. There are no minor ormajor losses used in the system analysis. Determine the x (horizontal) and y (vertical)components at support C. The figure is based on a vertical view of the system.
Draw the load flow diagram for column C1
Determine the moments at all supports. Answer key: MBA = 2 kN-m; MBC = -2 kN-m; MCB = 4.46 kN-m; MCD = -4.46 kN-m; MDC = 0.66 kN-m; MDE = -0.66 kN-m; MED = 3.27 kN-m
Design a purlin for a roof truss having the following data:Span of the truss = 6.0mSpacing of truss = 3m c/c.Inclination of roof = 30oSpacing of Purlin = 2m c/cWind pressure = 1.5 kN/m2Roof coverage= A.C Sheeting weighing 200 N/m2Provide a channel section Purlin.
note: SN = 18, to the topload will be 118kN
A. Design an axially loaded short square tied column for Pu = 2600 KN if fc' = 28 MPa and fy = 350 MPa. Initially assume p = 0.02. Sketch the column cross-section and rebar arrangement. Use NSCP 2015 standard