Oil flows through a smooth pipe of diameter D-4 cm between points (1) and (2) that are 4 m apart at a flow rate Q - 40x 10 m/s. The pressure at the lower end is 400 kPa and the pipe is inclined at 0 - 30 degrees. Consider dynamic viscosity u = 0.40 kg/(m s) and density p- 900 kg/m for the oil. 1. Calculate the pressure P, in Pascals when the flow is upwards 2. Calculate the pressure P, in Pascals when the flow is downwards

Oil flows through a smooth pipe of diameter D-4 cm between points (1) and (2) that are 4 m apart at a flow rate Q - 40x 10 m/s. The pressure at the lower end is 400 kPa and the pipe is inclined at 0 - 30 degrees. Consider dynamic viscosity u = 0.40 kg/(m s) and density p- 900 kg/m for the oil. 1. Calculate the pressure P, in Pascals when the flow is upwards 2. Calculate the pressure P, in Pascals when the flow is downwards

Name: Oil flows through a smooth pipe of diameter D = 4 cm between points (
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Oil flows through a smooth pipe of diameter D = 4 cm between points (1) and (2) that are 4 m apart at a flow rate Q = 40x 10° m/s. Thepressure at the lower end is 400 kPa and the pipe is inclined at 0 = 30 degrees. Consider dynamic viscosity u = 0.4

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.
A certain garden hose is advertised to be able to deliver 550 gallons of water per hour. If the hose if 50 feet long and has an inside diameter of 5/8 inch, estimate the water pressure necessary to deliver this much water, assuming laminar flow and viscosity at 1.002 x 10-3 kg/(m-s)
A bicycle tire is fi lled with air at an absolute pressure of169.12 kPa, and the temperature inside is 30.0 °C. Supposethe valve breaks, and the air starts to exhaust out of the tireinto the atmosphere (pa = 100 kPa absolute and Ta =20.0 °C). The valve exit is 2.00 mm in diameter and is thesmallest cross-sectional area of the entire system. Frictionallosses can be ignored here; one-dimensional isentropicflow is a reasonable assumption. (a) Find the Machnumber, velocity, and temperature at the exit plane of thevalve (initially). (b) Find the initial mass flow rate out ofthe tire. (c) Estimate the velocity at the exit plane using theincompressible Bernoulli equation. How well does thisestimate agree with the “exact” answer of part (a)? Explain.
What is the volume flow rate for water (viscosity= .0010 Pa×s) through a length of pipe L= 0.60m and pipe radius r= 1.03cm if the pressure difference across this length of pipe is 5.2 kPa? Note that 1 kPa= 1000 Pa. What would the volume flow rate be if the same pipe had a radius that is reduced by 21% (i.e. the radius is 79% of its previous value)? Let's call this flow rate Q1. What is the ratio of Q1 to the original flow rate Q? Express this as a decimal number.
Find the head lost due to friction in a pipe of radius 20 cm and length 50m, through which oil is flowing at a velocity of 5 m/s using (a) Darcy formula (b) Chezy formula for which C= 65, Take Specific gravity of the oil is 0.8 and Dynamic viscosity is 8 X 10-3 poise.
Figure 1) shows a tank of 20∘C water with a nozzle h = 27 cm below the surface. Bernoulli's equation applies to the flow between points 1 and 2 on the streamline, but not to the flow between points 2 and 3.What is the volume flow rate through the nozzle in L/min ? Assume that the water level in the tank is held constant.
A circular pipe flow, the diameter d=50mm, mean velocity of water flow in the pipe v=1.5m/s, kinematic viscosity v = 0.89x10m/s when water temperature is 25°C. Judge flow regime in the pipe.
A fluid has a kinematic viscosity ν=15x10-6 m2 s-1 and a density ρ=1 kg m-3. In a given industrial application we have a straight, circular pipe of radius 0.1 m and length 11.8 m. A pressure drop of Δp=4.8 Pa is imposed to drive the flow. Assuming a fully developed and steady state flow in the entire pipe, find the wall shear stress magnitude in SI units? Give your answer to three decimal places.
SAE 10 oil at 20°C flows through the 4-cm-diameter vertical pipe of Fig. P6.30. For the mercury manometer reading h = 42 cm shown, (a) calculate the volume flow rate in m3/h and (b) state the direction of flow.
At 0.5m/s, engine oil with a kinematic viscosity of 0.00024m2/s flows inside an annulus. A 3-in schedule 40 (ID= 3.068in) and a 1-in schedule 40 (OD= 1.32in; ID= 1.049in) concentric steel pipe 10cm long form the annulus. What is the pressure drop in terms of oil meters?
Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. Consider a venturi with a small hole drilled in the side of the throat. Thishole is connected via a tube to a closed reservoir. The purpose of theventuri is to create a vacuum in the reservoir when the venturi is placed inan airstream. (The vacuum is defined as the pressure difference below theoutside ambient pressure.) The venturi has a throat-to-inlet area ratio of0.85. Calculate the maximum vacuum obtainable in the reservoir when theventuri is placed in an airstream of 90 m/s at standard sea level conditions.
Fluid Mechanics Laboratory Experiment No.5 Pitot Static Tube The Discussion 2 — When the pitot tube is moved vertically inside the pipeline, why does it yield different flow velocities? Explain 3 — If the pitot tube is not perfectly aligned with the current direction, it produces errors in the measurements of static pressure and total (pool) pressure, Why? Explain. 4 — When flow velocity increases, it alters the shape of the flow velocity profile. Clarify 5 — What are the advantages and disadvantages of the pitot static tube. 6 — Does altering fluid temperature influences the results obtained by pitot static tube? clarify