A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.89 ksi. Determine the absolute maximum shear stress on the inner surface of the cylinder wall. O 42.6 ksi O 31.2 ksi O 39.7 ksi O 36.1 ksi O 33.5 ksi

A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.89 ksi. Determine the absolute maximum shear stress on the inner surface of the cylinder wall. O 42.6 ksi O 31.2 ksi O 39.7 ksi O 36.1 ksi O 33.5 ksi

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.3P: A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is...

See similar textbooks

Similar questions

.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.40 ksi. Determine the absolute maximum shear stress on the inner surface of the cylinder wall.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and it's length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa and the circumferential stress is limited to 60 MPa 2) A compound thin cylinder has a common diameter of 100 mm, and the inner cylinder has a thickness of 2,5 mm. The radial pressure between the two cylinders is 200 KPa and the difference between the two common diameters before shrinkage was 0,004305 mm. E=200 GPa Determine : A) Thickness of the outer cylinder B) Resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 KPa
Determine the maximum shear stress (in ksi). AT = 654 lb ft Diameter =3.7 in J =1.5in4 G = 11,000 ksi
Q2. A mild steel shaft transmits 21 kW at 250 r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa.
The assembly shown below consists of a brass shell (1) fully bonded to a ceramic core (2). The brass shell [E = 115 GPa; α = 18.7 x 10-6 /°C] has an outside diameter of 50 mm and an inside diameter of 35 mm. The ceramic core [E = 290 GPa; α = 3.1 x 10-6 /°C] has a diameter of 35 mm. At a temperature of 15°C, the assembly is unstressed. Determine the largest temperature increase that is acceptable for the assembly if the normal stress in the longitudinal direction of the brass shell must not exceed 80 MPa.
A cylinder having an internal diameter of 16 inches and external diameter of 26 inches is subjected to 1,500 psi external pressure and internal pressure of 9,000 psi. Determine the hoop stress on the outer surface of the cylinder. A. 7,642.84 psi C. 5,284.67 psi B. 6,466.24 psi D. 8,833.02 psi
1.A cylindrical pressure vessel is 500 mm in diameter and has a wall thickness of 22 mm. If it is subjected to an internal pressure of 5 MPa, determine the tangential and longitudinal stresses developed in the cylinder.
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
Consider a tube having a rectangular cross-section as shown below. The tube is subject to two twisting moments of 70 N - m . Determine the average shear stress developed at point A. The tube is fixed at the other end. a) 1.75 MPa b) -1.65 MPa c) 4.086 MPa d) 2.095 MPa If your doing it fast, I will rate you...