Oil (SAE 30) at 15.6 °C flows steadily between fixed, horizontal, parallel plates. The pressure drop per unit length along the channel is 15 kPa/m, and the distance between the plates is 3 mm. The flow is laminar. Determine: (a) the volume rate of flow (per meter of width), (b) the magnitude of the shearing stress acting on the bottom plate, and (c) the velocity along the centerline of the channel. (a) q = 8.88 10^-5 m2/s (b) Txy= N/m? 22.5 (c) umax = 0.0444 m/s

Oil (SAE 30) at 15.6 °C flows steadily between fixed, horizontal, parallel plates. The pressure drop per unit length along the channel is 15 kPa/m, and the distance between the plates is 3 mm. The flow is laminar. Determine: (a) the volume rate of flow (per meter of width), (b) the magnitude of the shearing stress acting on the bottom plate, and (c) the velocity along the centerline of the channel. (a) q = 8.88 10^-5 m2/s (b) Txy= N/m? 22.5 (c) umax = 0.0444 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air flows through a duct at 2,700 cubic feet per minute (CFM). After several feet and a few vents, the air-flow decreases to 1,890 CFM. What is the percent drop that has occurred? (Simplify your answer completely.)
Calculate the power required per meter of width of stream to force lubricating oil through the gap between two horizontal flat plates under the following conditions: Distance between plates, 6 mm Flow rate of oil per meter of width, 100 m3h Viscosity of oil, 25 cP Density of oil, 0.88 g/cm3 Length of plates, 3 m Assume that the plates are very wide in comparison with the distance between them and that end effects can be neglected.
SAE 10 oil at 20 °C flows in a vertical pipe of diameter 2.5 cm.It is found that the pressure is constant throughout thefluid. What is the oil flow rate in m3/h? Is the flow up ordown?
Fluid Mechanics Laboratory Experiment No.5 Pitot Static Tube The Discussion 2 — When the pitot tube is moved vertically inside the pipeline, why does it yield different flow velocities? Explain 3 — If the pitot tube is not perfectly aligned with the current direction, it produces errors in the measurements of static pressure and total (pool) pressure, Why? Explain. 4 — When flow velocity increases, it alters the shape of the flow velocity profile. Clarify 5 — What are the advantages and disadvantages of the pitot static tube. 6 — Does altering fluid temperature influences the results obtained by pitot static tube? clarify
Example: A fan of diameter 0.7 m running 1500 rpm delivers 140 m3/min of air at 15C against 75 mm of water total pressure when the total effeciency is 86%. Determine the volume of air delivered, total pressure and power consumed, if (a) the air temperature is 50C. (b) the air temperature is 50C and the fan speed is 1700 rpm. (c) the same conditions as (b) but a 0.6 m diameter, geometrically similar fan is used.
Carbon dioxide at 125 °C flows over a flat plate at 0.4 m/s. If we use 3.5 x 105 as the critical Reynolds number, what will be the distance along the plate that you can expect the flow to remain laminar? What is the distance if you use the range of values given by my fluid’s textbook (Cengal and Cimbala) of 1 x 105 for ideal situations to 5 x 105 for typical engineering situations?
Figure 1) shows a tank of 20∘C water with a nozzle h = 27 cm below the surface. Bernoulli's equation applies to the flow between points 1 and 2 on the streamline, but not to the flow between points 2 and 3.What is the volume flow rate through the nozzle in L/min ? Assume that the water level in the tank is held constant.
Vortex shedding can be used to design a vortex flowmeter(Fig. 6.34). A blunt rod stretched across the pipe shedsvortices whose frequency is read by the sensor downstream.Suppose the pipe diameter is 5 cm and the rod is acylinder of diameter 8 mm. If the sensor reads 5400 countsper minute, estimate the volume flow rate of water in m 3 /h.How might the meter react to other liquids?
6.) A 100-mm diameter plunger is being pushed at 60 mm/sec into a tank filled with oil having sp.gr. of 0.82.If the fluid incompressible, how many N/s of oil is being forced out at a 30-mm diameter hole? Answer: 3.78 N/s Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3 Please.. explain more easy
SAE 50W oil at 20°C flows from one tank to another through a tube 220 cm long and 5 cm in diameter. Estimate the flow rate in m3/hr if z1 = 2 m and z2 = 0.8 m. For SAE 50W oil, take ρ = 902 kg/m3 and μ = 0.86 kg/m-s. Take π = 22/7. The flow rate is m3/hr.