Oil sg = 0.75 is flowing through a pipe%3Dwith 6 in diameter under a pressure 15psi. The total energy is 58.6 ft.lb/lb andthe pipe is 8ft from the datum plane.Determine flow rate (in cubicfeet/second).

A flow rate or rate of flow may relate to the amount of fluid passing through any part of the system…

Answered: Oil sg = 0.75 is flowing through a pipe…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A liquid of specific gravity of 1.75 flows in a 6 cm horizontal pipe. The total energy at certain point in the flow is 80 J/N (joules/newton). The elevation of the pipe above the fixed datum is 2.6 m. If the pressure is 75 kPa. Determine the velocity of flow in m/s. A.23.86 b.32.45 c.37.85 d.42.25l
Determine the diameter of an orifice that permits a tank of horizontal crosssection 1.5m2 to have its liquid surface draw down at the rate of 160 mm/sfor a 3.35-m head on the orifice. Use C=0.63.
Glycerin flows through a system composed of pipes at a rate of 7.735 m3/s, calculatethe velocity in each pipe section and the pressure that is generated in section 1 and 2
Completely solve and box the final answers. Write legibly Brake Horsepower of Centrifugal Pump. Using Fig. 3.3-2 and a flowrate of 60 gal/min, do as follows. a.Calculate the brake hp of the pump using water with a density of 62.4 lbm/ft3. (ans. 0.81 hp or 0.60 kW). and also, Compare with the value from the curve. b.Do the same for a nonviscous liquid having a density of 0.85 g/cm3. (ans. 0.69 hp or 0.51 kW)
The pump in the figure discharges water at 60 liters/sec. Neglecting losses and elevation changes.Assume unit weight of water is 9.81 kN/m³. Determine the mechanical efficiency of the pump if thepower input recorded is 120HP.P2=409 kPaD2-4cm 091.5% 82.5%90.4%95.8%PP₁=125 kPaD₁=10cm Ø
Oil (SG=0.82) entering a pump through an 180mm diameter pipe at 35kPa has a flow rate of 0.07 m^3/s. It leaves the pump through a 120mm diameter pipe at 120 kPa. Assuming that the suction and discharge sides of the pump are at the same elevation, find the horsepower delivered to the water by the pump (746 watts = 1 HP). Illustrate the problem and show your complete solution.
Derive an expression for the capillary rise h for a fluid of surface tension a and contact angle between two vertical plates a distance W apart, see figure below. What will be h for water at 20°C if W= 0.25mm?
Water flows through the turbine shown at a rate of 0.386 m3/s. The pressures at points A and B are 161.2 kPa and -19.6 kPa, respectively. What is the electrical power generated by the turbine if it is 85% efficient?
Length of Pipe 1 = 300 m Length of Pipe 2 = 240 m Length of Pipe 3 = 210 m Length of Pipe 4 = 450 m *Pipe 2 and Pipe 3 are parallel Diameter of Pipe 1 = 200 mm Diameter of Pipe 2 = 150 mm Diameter of Pipe 4 = 250 mm discharge of the pipe system = 45 Liters/second Total hf = 8 meters f= 0.02 What is the diameter of Pipe 3? (in mm)
9.The pump shown delivers 115 li/s of oil, sg = 0.84, toreservoir D at elevation 72 m. The energy lost in thesuction line is 3.2 J/N and in the discharge line is 7.6 J/N. a.Compute the total head added by the pump. b.How many kW does the pump supply the system? c.If the pump is 85% efficient, how much power does it need?
diameter of pipe = 200mm Cc = 0.61Cv = 0.97 Considering the figure, what is the flow of water?
Q2: Water is flow by arate = (v/( “7— /20) m¥/s , the water is still stable due to using a pump as shown in figure below. A pipe of rectangular cross sectional area of dimension (10 *20 ) cm is used to connect the two reservoir, friction factor for the pipes(£=0.02), if K value in the entrance and in the exit are 0.1 and 1 respectively. Calculate the pump power:- ElL15m Water EL10m Water = o cotanantwe *10 = 50 m——

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Oil sg = 0.75 is flowing through a pipe %3D with 6 in diameter under a pressure 15 psi. The total energy is 58.6 ft.lb/lb and the pipe is 8ft from the datum plane. Determine flow rate (in cubicfeet/ second).