Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The friction factor of the pipe is 0.0225. The pipe slopes down at 10 degrees from the horizontal. Determine the difference in pressure between the start of the pipe to the end of the pipe.

Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The friction factor of the pipe is 0.0225. The pipe slopes down at 10 degrees from the horizontal. Determine the difference in pressure between the start of the pipe to the end of the pipe.

Name: Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The friction factor of the pipe is 0.0225. The pipe slopes down at 10 degrees from the horizontal. Determine the difference in pressure between the start of the

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.27P

See similar textbooks

Similar questions

Water is flowing at a rate of 0.5 m³/s through a rough pipe with a diameter of 0.5 m and a length of 800 m. Assuming the average roughness height (k) is 0.15 mm, determine: a) the friction coefficient, b) the wall shear stress, c) the velocity at the centerline and 200 mm away from the pipe wall.
Water flows in a 15-cm-diameter pipe at a velocity of 1.8 m/s. If the head loss along the pipe is estimated to be 19 m, the required pumping power (in kW) to overcome this head loss is ?"
A 6-cm-diameter horizontal water pipe expands gradually to a 9-cm-diameter pipe. The walls of the expansion section are angled 10° from the axis. The average velocity and pressure of water before the expansion section are 7 m/s and 150 kPa, respectively. Determine the head loss in the expansion section and the pressure in the larger-diameter pipe.
In a pipe conveying steady flow of incompressible fluid, what factor determines the magnitude of flow velocity? O Friction O Temperature © Cross-sectional area
Water flows in a 15-cm-diameter pipe at a velocity of 1.8 m/s. If the head loss along the pipe is estimated to be 16 m, the required pumping power to overcome this head loss is
Water flows at a rate of 0.035 m3/s in a horizontal pipe whose diameter is reduced from 15 cm to 8 cm by a reducer. If the pressure at the centerline is measured to be 480 kPa and 457.3 kPa before and after the reducer, respectively, determine the pressure loss in the reducer. Take the density of water to be ρ = 1000 kg/m3 Ans: [22,300 Pa]
A pipe line of length 2000 m is used for power transmission. If 110 kW power is to be transmitted through the pipe in which water having a pressure of 490.5 N/cm2at inlet is flowing. If the pressure drop over the length of pipe is 98.1 N/cm2and ff = 0.0065.Determine:The diameter of the pipe and the volume flow rate; and If a nozzle is introduced at the end of the pipe, what would be its diameter and the power transmitted.
By searching the web or any other source, discuss how pumps in series and pumps in parallel affect flow rate and pressure.
Air at 105 kPa flows upward through a 6-cm-diameter inclined duct at a rate of 65 L/s. The duct diameter is then reduced to 4 cm through a reducer. The pressure change across the reducer is measured by a water manometer. The elevation difference between the two points on the pipe where the two arms of the manometer are attached is 0.20 m. Determine the differential height between the fluid levels of the two arms of the manometer. Take air density as 1.225kg/m3
Water at 75 degrees Celsius is flowing horizontally at a rate of 1.6 m^3/min in a pipe. It enters a 3-in 45 degree elbow and is diverted upwards into a connecting pipe. The diameter of the outlet is 2in. If the pressure just before the elbow is 78 kPa, determine the magnitude and direction of the force necessary to keep the elbow in place. Assume frictional losses in the elbow are negligible.
A fluid enters a pipe at speed v1=0.1 m/s. the diameter of the tube is d=200mm and the fluid flowing through the pipe is mercury with a specific gravity of 13.6. the mass flow rate is
For fully developed laminar pipe flow in a circular pipe, the velocity profile is given by u(r)= 2(1- r2 / R2) in m/s. Where R is the inner radius of the pipe. Assuming that the pipe diameter is 4 cm. find the maximum and average velocities in the pipe as well as the volume flow rate.