Water drains from a pressurized tank (50 kPa gage) with a height of 200 m through a 200 m horizontal pipe, with a diameter of 0.1m, at a rate of 0.0371 m³/s. The density of water is 1000 kg/m3 and the dynamic viscosity is 1.12 x 10 - 3 Ns/m². Consider the Darcy friction factor equal to 0.0355 and the minor losses to be negligible. If a turbine is connected at the end of the pipe after which the water flows into a lake, then the specific work of the turbine would be equal to

Water drains from a pressurized tank (50 kPa gage) with a height of 200 m through a 200 m horizontal pipe, with a diameter of 0.1m, at a rate of 0.0371 m³/s. The density of water is 1000 kg/m3 and the dynamic viscosity is 1.12 x 10 - 3 Ns/m². Consider the Darcy friction factor equal to 0.0355 and the minor losses to be negligible. If a turbine is connected at the end of the pipe after which the water flows into a lake, then the specific work of the turbine would be equal to

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a fully developed flow of water in a pipe having diameter 10 cm, velocity 0.1 m/s and kinematic viscosity 10-5 m²/s, the value of Darcy friction factor is
Water enters a piping system with a diameter of 0.1016 m from a reservoir with a volumetric flow rate of 0.1893 m3/min. Determine whether the flow is laminar or turbulent if, during the winter, the dynamic viscosities of μ = 1.308×10-3 Pa·s and 0.687×10-3 Pa·s during the summer.What is the length of pipe necessary to reach a fully developed flow?
Determine the head loss due to friction of an oil of specific gravity 0.77 and viscosity 0.85 poise is flowing through a pipe at the rate of 3.7 m/s. Assume the pipe diameter as 29 cm and the length of the pipe as 5618 cm. Oil Density (in kg/m3) Reynold's Number - Co-efficient of friction - Head loss due to friction
A pump is being used to transport a liquid food product (density p=1000kg/m^3, viscosity 0.001 Pa s) from holding tank to filling a machine at a mass flow rate of 2 kg/s. The liquid level in the holding tank is 10 m above the pump, and the filling machine is 5 m above the pump. There is 100 m of 2-in nominal diamter sanitary pipe between the holding tank and the filling machine, wiht one open globe valve and four regular 90° flanged elbows in the system. Within the system, there is a heat exchange which causes 100 kPa of pressure drop due to friction. The holding tank is open to atmosphere, and filling machine is running at a pressure of 1.5 atm. The diamter of the filling machine pipe is 3cm. A: What is the volume flow rate of the system? B: What is the diamete of the pipe? C: What is the average velocity inside the pipe? D: What is the reynolds number of the flow in the pipe? E: What is the flowing type?
A horizontal concrete pipe (material roughness = 1.3 mm) with diameter of 5 cm andlength of 300 m is used to transport acetic acid. The density and dynamic viscosity ofthe acetic acid is 1049 kg/m3and 0.001155 Pa.s. If the flow rate required for thetransportation is 30 litre per minute: Determine the required pump power to overcome the head loss using Moody chartand Colebrook-White equation; Determine the required pump power to overcome the head loss using Altshul’scorrelation as shown in the equation below; Compare the difference of pumping power between answers obtained in Q5(a) andQ5(b) and discuss the validity/accuracy for Altshul’s correlation.
[CE Hydraulics] 5. For the case of turbulent flow in rough pipes, does the friction factor depend on the Reynolds number? Why?
If the difference between the total pressure and static pressure in an air duct is measured by a pitot tube to be 6.5 cm H2O, what is the flow velocity in m/s? Density of water is 998 kg/m3, and g = 9.81 m/s2. 3 signififcant figures answer
Calculate the head loss due to friction in a pipe of diameter 25 cm and length 60 m, through whichwater is flowing at a velocity of 2 m/s. (a.) Darcy formula (b.) Chezy’s formula for which C = 60.
Water at 10 ° C flows from a large reservoir to a smaller one through a 5 - cm - diameter cast iron piping system, as shown in Fig. Determine the elevation z, for a flow rate of 6 L / S. Note that Properties The density and dynamic viscosity of water at 10e are p999.7 kg / m and 1.307 X100 kg / m3
A fluid with SG: 0,888 and viscosity: 0,8 Pa s flows in a horizontal pipe of diameter :5 cm and length: 40 m .The measured velocity profile is of parabolic shape . The amount of pressure difference between inlet and exit of the pipe is 648,76 kPa. Determine the amount of flow rateANSWER: 0,0031 m3/s
A venturi meter equipped with differential pressure gage is used to measure the flow rate of water with a mass density of 999.1 kg/m^3 through a 5 cm diameter horizontal pipe. The diameter of the venturi neck is 3 cm and the measured pressure drop is 5 kPa. Taking the discharge coefficient to be 0.98, determine the average velocity through the pipe in m/s. Include a diagram in your solution. a.3.2 b.4.2 c.2.2 d.1.2
A pipeline transporting engine oil of 3.5 m3/s at 40⁰C branches out into two parallel pipes made of commercial steel but reconnects downstream. Pipe A is 750 m long and has a diameter of 50 cm while Pipe B is 1200 m long with a diameter of 50 cm. Neglecting minor losses, determine the following:a) Flow rates (in m3/s) through pipe A and pipe B.(Hint: Assume similar flow frictional factor for initial calculations and determine the correct frictional factor using Colebrook equation).b) Actual head losses (in m) in pipe A and pipe B