Please show work o1.) A voltage amplifier has an input resistance Rin = 5kQ, output resistance Rout = 1OKQ, and a voltage gainA, = -65 V/V. A voltage source is connected to the amplifier, and is modeled as a source voltage, V, having asource resistance R, = 1kQ. Finally, a load resistor RL = 25kQ is connected to the output of the amplifier, acrosswhich is the output voltage Vo.a.Sketch the linear two-port model of the voltage amplifier, including the source and loadresistances.b. Find the voltage gain VVs in V/V and dB.

a The parameters of the voltage amplifier are given, The voltage amplification level is calculated…

ol.) A voltage amplifier has an input resistance Rin = 5kQ, output resistance Rout = 10k2, and a voltage gain A, = -65 V/V. A voltage source is connected to the amplifier, and is modeled as a source voltage, V, having a source resistance R, = 1kQ. Finally, a load resistor R1 = 25kQ is connected to the output of the amplifier, across which is the output voltage Vo. a. Sketch the linear two-port model of the voltage amplifier, including the source and load resistances. b. Find the voltage gain VVs in V/V and dB,

ol.) A voltage amplifier has an input resistance Rin = 5kQ, output resistance Rout = 10k2, and a voltage gain A, = -65 V/V. A voltage source is connected to the amplifier, and is modeled as a source voltage, V, having a source resistance R, = 1kQ. Finally, a load resistor R1 = 25kQ is connected to the output of the amplifier, across which is the output voltage Vo. a. Sketch the linear two-port model of the voltage amplifier, including the source and load resistances. b. Find the voltage gain VVs in V/V and dB,

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

Suppose that each output channel of a computer’ssound card can be represented by a 1-V ac sourcein series with a 32-Ω resistor. Each channel ofthe amplifier in the external speakers has an inputresistance of 20 k , and must deliver 10 W intoan 8-Ω speaker. (a) What are the voltage gain, currentgain, and power gain required of the amplifier?(b) What would be a reasonable dc power supplyvoltage for this amplifier?
Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. Calculate the current gain, the input resistance, and the output resistance.
Suppose we have a two-stage cascaded amplifier with an ideal transconductance amplifier as the first stage and an ideal transresistance amplifier as the second stage. What type of amplifier results and what is its gain in terms of the gains of the two stages? Repeat for the amplifiers cascaded in the opposite order.
Suppose we have a resistive load that varies from 5 kΩ to 10 kΩ .We connect this load to an amplifier, and we need the voltage across the load to vary by less than 1 percent with variations in the load resistance. What parameter of the amplifier is important in this situation? What range of values is allowed for the parameter?
The figure below shows an inverting amplifier connected to a load RL. Determine the power gain of the amplifier. power gain for the amplifier, G, is defined as the power ratio that reaches the load RL versus the power supplied by the source VS.
Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: 1- Determine the Q point, then illustrate it on the transistor I-V characteristic curves. 2- Is the transistor in the active region? Explain thoroughly. 3- Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. 4- Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. 5- Calculate the current gain, the input resistance, and the output resistance.
Class À Amplifier questions A. If the amplifier input signal is 10 mV, what is the effective output power Po(rms) and the efficiency. B. determine whether the amplifier operate in the class A region. C.If the amplifier is not operated in the class A operating region, what is the required bias resistorRB to ensure class A operation.
amplifier has a gain of unity andVcc= 25Vdc, RL= 8Ω and Vi(p-p)= 34V.a. Calculate the input power, the output powerand the efficiency of the amplifier.b. Consider the operation mode that the two output transistors dissipate the maximum power. For this operation mode, find the output voltage across the load and the power dissipated by each transistor.
On which criteria the power amplifiers are classified? What is the operating point of a class-A power amplifier? What is meant by efficiency? How much efficiency will be obtained in a class-A power amplifier? What are the applications of power amplifiers?
A certain amplifier has an open-circuit voltage gain of unity, an input resistance of 1 MΩ and an output resistance of 100 Ω. The signal source has an internal voltage of 5 V rms and an internal resistance of 100 kΩ. The load resistance is 50 Ω. If the signal source is connected to the amplifier input terminals and the load is connected to the output terminals, find the voltage across the load and the power delivered to the load. Next, consider connecting the load directly across the signal source without the amplifier, and again find the load voltage and power. Compare the results. What do you conclude about the usefulness of a unity-gain amplifier in delivering signal power to a load?
Sketch the inverting amplifier and derive an expression for the gain of the amplifier.
Activity 2:The amplifier circuit below has a single ac input and two ac outputs. Assuming transistorparameters of ß = 200 and VBE = 0.7 V:(2-a) Determine the Q point.(2-b) Is the transistor in the active region? Explain thoroughly.(2-c) Construct the T-model of the transistor with all parameters labelled and evaluated.Assume room temperature.(2-d) Draw a complete small-signal circuit model, then find the voltage gain for both outputs.(2-e) Based on the analysis results, what is the function of this circuit? Suggest a properapplication.(2-f) Use Multisim to verify all of your results. Compare and comment.(2-g) Assuming that each output is feeding a 100-kΩ resistor, determine the total voltage gainand current gain for both outputs. Also, calculate the amplifier input resistance and theamplifier output resistances.