On a support of mass M hanging from a stiff spring k falls from the height Ha body of mass m and adheres to it. Determine the maximum elongation of the spring. Mg mg Ymáx =+(1+ VI+ 2kH/(M + m)g] Утах k ans.

On a support of mass M hanging from a stiff spring k falls from the height Ha body of mass m and adheres to it. Determine the maximum elongation of the spring. Mg mg Ymáx =+(1+ VI+ 2kH/(M + m)g] Утах k ans.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.75P

See similar textbooks

Related questions

Q: A force of 10 kN is applied to the hook. If the CB cable is made of steel (E= 200 GPa) determine the…

A: According to the details provided in the question, we need to calculate the Displacement of BC.

Q: 5.14. A carriage spring centrally loaded and simply supported at the ends has 10 steel plates each 5…

A: In this inquiry, we know that a carriage spring with 10 steel plates, each 5 cm broad by 6 mm thick,…

Q: Determine the spring constant k4 (N/m) if the extension of the whole system is 1.04 m when a force…

Q: Spherical Tank Problem 3 The pressures Pa and Pe in the differential manometer gage are 154.415 kPag…

Q: A spring stored an energy U of 50 joules. Determine the deflection x if the spring constant is k =…

A: Given data, K= 6969 N/m U= 50 j Let x be the deflection in spring.

Q: Determine R if the equivalent spring stiffness constant (keq) of the spring system is 500 N/m R N/m…

Q: ww os 240 mm

A: A vector is a physical quantity that has magnitude and direction both. A scalar is a physical…

Q: 400 N/m 400 N/m 100 N 200 N ww

Q: Determine the vertical displacement of point C. EI is constant. Use the method of virtual work.…

A: Deflection at point C is determined by virtual work as given

Q: 04m d=0.15m D

Q: How much work is done by the force in the spring when the slender rod rotates clockwise about the…

Q: *44. The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod is…

Q: When a 6 kg load is hung at point O and member AO is adjusted until it is horizontal, the angle is…

A: Given: Let us consider the given data, m=6 kgθ=35° To find: The moments about AD,BD, and AO.

Q: Determine R if the equivalent spring stiffness constant (keq) of the spring system is 500 N/m

Q: The bar supported by a pin at B and a cable at A carries a load of 260 N at C. Neglecting the weight…

Q: Determine the resultant internal bending moment acting on the cross section at point C in the beam…

Q: The 75-lb block has a downward velocity of 2 ft>s when it is 3 ft from the top of the beam.…

A: given data as per question mass of the beam = 75 lb

Q: When the 100-lb block is at h = 3 ft above the cylindrical post and spring assembly, it has a speed…

A: Above loading is Type of impact loading. In impact loading , stress generated in the body is higher…

Q: The cylinder has a mass of 30 kg and is mounted on an axle that is supported by bearings at A and B.…

Q: Q8/ While steadily pushing the machine up Determine the components of P which are Parallel and…

Q: 0.3 m k = 200 N/m 0.4 m

A: Let F be the force in the spring as shown in figureThe angle θ can be calculated from geometrytan…

Q: equations of the elastic curve for the shaft using the x1 and x2 coordinates. Take El as constant…

Q: Current Attempt imProgress Determine the bending moment Min the beam at the point located 0.44 m to…

Q: Determine the displacement of point C. Use the method of virtual work. EI is constant. Solve Prob.…

A: If a rigid body or a system of bodies is present having equilibrium condition under various forces…

Q: Q8/ While steadily pushing the machine up on an incline surface, a person exerts 180 N force P as…

A: Firstly find out the parallel component of the incline surface Pt=180cos(10+15)=163.1 N

Q: 1. The kinetic energy due a rolling disk with or without slipping, is given by: }mv? D) T =lgw +mv.…

A: Since rolling motion is a combination of rotation and translation motion, thus a body in rolling…

Q: The homogeneous box has mass m. The magnitude of force Pis slowly increased until motion occurs.…

Q: 1. Draw the FBD of the entire structure (weight acts at point G) 0.5 m 0.5 m 0.5 m 1m B D 0.5 m E

A: Dear student, According to the guidelines, I am allowed to answer only one…

Q: Determine the shear force at x=0.15 m of the beam subjected to the elliptical and uniform load…

A: According to my calculation the SF at x equal to 1.5 if 43.75 N. Please check your options if there…

Q: Compute the work done by the indicated force when the disk undergoes the specified displacement…

Q: The 80 kg block hits the simply supported beam of steel at its midspan after a drop of 10 mm as…

A: Given, m=80kgLoad , W=mgW=80×9.81W=784.8N RA=RB=W2RA=RB=392.4NMoment at…

Q: The 80-lb weight is dropped from rest at a height h = 4 ft onto the end of the A-36 steel W6 * 12…

A: To find-: The maximum bending stress developed in the beam. Given-: The weight of the body is W=80…

Q: Draw the free body diagram. 80 mg 60 20 650 mm 200 925 mm mm By

A: Solution: The free body diagram of the inclined beam is shown below:

Q: Determine the shear force V in the beam at the point located 4.50 m to the left of point C. The…

A: Given:To determine the shear force in the beam at 4.50m from C.Reaction at A, RA=65.6KNUDL, w=7.0…

Q: Determine the displacement of points B and C of the beam shown in Fig. a. EI is constant.

A: Given : A bending moment Mo is applied at point C of the cantilever beam of length L and EI is…

Q: 0.7 m 20⁰ 0.3 m FB B 25 If FB = 120 N and Fc = 140 N, a) Draw the Free-Body Diagram 30° Fc the bolt…

Q: The beam shown has an overall length L of 2 metres. A uniform distributed load of 3.7 kN/m is…

A: In a beam, resisting shear force at any given section can be calculated as sum of all the shear…

Q: 3–23. The springs BA and BC each have a stiffness of 500 N/m and an unstretched length of 3 m.…

A: Given:- k=500 N/m AC=6m F=175 N To find:- Displacement of the cord

Q: Q6) The block has a mass of 15kg and rests on the smooth plane. Determine the .unstretched length of…

Q: 3 What ore the reaction forces cat A+B in the following sstem when a. h=0 b.h=a0om l_a50mm 250mm 1…

A: A pin support will exert both horizontal and vertical components of reaction. The support A is pin…

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Take: d1 =…

Q: Determine the radius of the turn, ircraft weighs 5000 lb and is bar 106.64 ft 230.79 ft

A: Aircraft Note: Student has posted three question and we are bound to answer one at time so first…

Q: To test the deflection on a uniform 100-kg beam, a boy of who weighs 50 kg exerts a pull of 150N on…

A: Given data: The mass of the beam is M=100 kg The mass of the boy is mB=50 kg The tension in the rope…

Q: Determine the x, y, z components of internal loading at a section passing through point B in the…

A: Given structure:

Q: springs having the stiffness shown. Determine the stretch of spring AC, S(AC): Select one: a. S(AC)…

Q: 275+Roll No N/m 250+Roll No N.M 4 m

Q: In each case, draw the estimated elastic curve: 4 m- 8 kN.m 2 kN/m 8 kN 4 kN

Concept explainers

Forced undamped vibrations

In mechanical engineering, vibration is expressed as the term that occurs due to an object's backward and forward movement about a point of equilibrium. Generally, there are three types of vibrations which are,

Question

On a support of mass M hanging from a stiff spring k falls from the height H a body of mass m and
adheres to it. Determine the maximum elongation of the spring.
Mg mg
-+(1+ V1+ 2kH/(M + m)g]
Утах
ans.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The triangular plate is fixed at its base, and A is given a horizontal displacement of Δs′= 4 mm. Suppose that L=800 mm.
The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Suppose that a= 640 mm
he region of safety in maximum shear stress theory contains which of the given shape *
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
Which of the following has the dimension for density. M1 L1 T-2 M-1 L1 T 2 M1L-3 M L -1 T-2
The load D has a mass of 220 kg and is being hoisted by the motor M with constant velocity. Determine the resultant normal force acting on the cross section at point E in the beam. Determine the resultant shear force acting on the cross section at point E in the beam. (Express answer to three significant figures and include appropriate units.)
AB, BC, CD, DE are each 2m long and the plane distance from A-D is 4m. Members are at right angles to each other. a) determine the vertical displacement at E b) determine the rotation at E E=200KN/mm^2 G= 80KN/mm^2 Iabce = constant = 25 x 10^-6 m^4 Jabce = constant = 50 x 10^-6 m^4
Determine the ratio of the MW 2 / MW 1 if t1 = 9 mins. and t2 = 7 mins.
ANSWER: h0.26916 m Show the complete solution.
The system below shows a system consisting of 4 masses that are turn. If R₁= R₂ = R3 = R4 = RA = RB = 10, determine the MA and MB placed in field A and field B.
Determine whether or not it is stable for that position. R=0.75m h=1.50m
The mass of the car is 1400 kg, which is evenly distributed over the four springs. The car's own weight compresses the springs into a pile for a distance of 20 cm. What is the characteristic frequency of car vibration in Hertz to one decimal place?