An electricity generation and distribution system consists of an AC generator, a step-up transformer, transmission lines and a series of step-down transformers providing AC electricity to the end users. The system has the following characteristics: Generator power output= 48.4 MW Generator voltage output = 24.2 kV rms Generator frequency - 50 Hz Transformer efficiency - 100% Step-up transformer loop ratio=1:10 Total resistance of transmission lines = 6.00 2 Series of step-down transformers: effective overall loop ratio = 1000:1 The system is represented in the schematic of Figure below. Assume it is operating at maximum power output. generator step-up transformer resistance of transmission lines 6.00 2 step-down transformer city (xi) On graph paper, sketch a graph of 'Voltage output (v)' versus 'Time (s)' for the output of the step-down transformer. Show two complete cycles.

An electricity generation and distribution system consists of an AC generator, a step-up transformer, transmission lines and a series of step-down transformers providing AC electricity to the end users. The system has the following characteristics: Generator power output= 48.4 MW Generator voltage output = 24.2 kV rms Generator frequency - 50 Hz Transformer efficiency - 100% Step-up transformer loop ratio=1:10 Total resistance of transmission lines = 6.00 2 Series of step-down transformers: effective overall loop ratio = 1000:1 The system is represented in the schematic of Figure below. Assume it is operating at maximum power output. generator step-up transformer resistance of transmission lines 6.00 2 step-down transformer city (xi) On graph paper, sketch a graph of 'Voltage output (v)' versus 'Time (s)' for the output of the step-down transformer. Show two complete cycles.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem 13.24P

See similar textbooks

Similar questions

A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
Three single-phase transformers, each rated 10MVA,66.4/12.5kV,60Hz, with an equivalent series reactance of 0.1 per unit divided equally between primary and secondary, are connected in a three-phase bank. The high-voltage windings are V-connected and their terminals are directly connected to a 115-kV three-phase bus. The secondary terminals are all shorted together. Find the currents entering the high-voltage terminals and leaving the low-voltage terminals if the low-voltage windings are (a) Y-connected and (b) - connected.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
The motors M1andM2 of Problem 3.45 have inputs of 120 and 60 MW, respectively, at 13.2 kV, and both operate at unity power factor. Determine the generator terminal voltage and voltage regulation of the line. Neglect transformer phase shifts.
In order to avoid difficulties with third-harmonic exciting current, which three-phase transformer connection is seldom used for step-up transformers between a generator and a transmission line in power systems. (a) Y- (b) -Y (c) Y-Y
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
Three single-phase, 50 kVA, 2300/230 V, 50 Hz transformers are connected to form a 3-phase, 2300/230V transformer bank. The equivalent impedance of each transformer referred to low voltage is 0.03 + j0.02 2. The 3-phase transformer supplies a 3-phase load, 120 kVA, 230 V, 0.9 p.f (lag). Determine (a) the transformer winding currents. (b) the voltage regulation. (comment on the obtained results)
A single-phase, 50kVA, 2400:240V distribution transformer has an impedance of 0.72+j0.92Ω from the high voltage winding and 0.007+j0.009Ω from the low voltage winding. This transformer is supplied by a feeder whose impedance is 0.3+j1.6Ω. Determine the voltage at the emitter terminal of the feeder when the load connected to the transformer secondary draws rated current at 240V with 0.8 lagging power factor. For this case, it is convenient to use the approximate circuit of the transformer given below. PLEASE, TYPE, HAND WRITING GETS UNDERSTANDING,
A 3-phase, 6,600/415-V, 2,000-kVA, delta-wye connected transformer has a primary impedance of of 5+ j 4.5 ohms and secondary impedance of 0.02 + j 0.45 ohms per phase. Calculate the Cu loss and the percent voltage regulation at full-load 0.8 p.f.
Given a 75 KVA, three phase transformer supplies the following initial loads: Capacitor bank drawing 25 kVAR and an inductive load drawing 36 kw, 0.715 power factor. Determine the maximum horsepower of an induction motor at 0.8 power factor and 85.5 percent efficiency that can be added to the load without overloading the trasnformer. Please show the detailed formula and solution and the correct answer.