One of the methods in measuring bulk volume for porosity measurement is direct calculation. By using the below data, determine the porosity for this core. Table 1: Parameters of rock-fluid Parameter Value, unit Core diameter 1.57 inch Core length 3 cm Dried core weight 100 g Saturated-brine core weight 110 g Brine density 1.30 g/cm³

One of the methods in measuring bulk volume for porosity measurement is direct calculation. By using the below data, determine the porosity for this core. Table 1: Parameters of rock-fluid Parameter Value, unit Core diameter 1.57 inch Core length 3 cm Dried core weight 100 g Saturated-brine core weight 110 g Brine density 1.30 g/cm³

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter7: Permeability

Section: Chapter Questions

Problem 7.22P: Refer to Figure 7.24. The following data were collected during the field permeability measurement of...

See similar textbooks

Similar questions

Not interested in the calculations, just want to see the graph so please display that for me instead of the e calculations. Note) For soil sample in Table 2, initial thickness of sample = 14.31 mm, sample area = 2827.433 mm^2 , dry weight measured at the end of test = 52.53 g, specific gravity = 2.7. (Please draw graph possible) Also Determine the compression index and expansion index using graph
Please solve fastly You are an oil and gas exploration reservoir engineer and your manger asked you to calculate the porosity for the following reservoir. Seismic data have been used to delineate reservoir structure (The length of this reservoir is about 200 meter, thickness is 1 meter and width is 0.8 km). A- Calculate the bulk volume of the reservoir in m3 . Make sure all the unit is consistent with each other. B- Assume that the pore spaces of the sediment in the oil-bearing unit are full of oil 32000m3. Calculate the porosity of the reservoir. C- Based on the porosity value. Is this negligible, poor, fair , or very good reservoir ( try to find table for reservoir classification based on porosity value)
Given following data, calculate a. Volume of measure b. Bulk density c. Absorption d. Void content
A rock mass has initial unit weight equal to y and, after loosening, it assumes unit weight y,. A coefficient of loosening (n) was defined by Müller (1978) n = Y A jointed sedimentary rock mass assumes a value ofn = 0.35 after loosening and 0.08 after recompaction. Calculate the corresponding val- of y1. (y = 27 kN/m') (b) Crystalline igneous rocks like granite, gneiss, and diabase have a range of values ofn = 0,35 to 0,50 after losening and 0.08 to 0.25 after recompaction. Compute the corresponding values of the unit weight (y.)
Refer to Figure 7.24. The following data were collected during the field permeability measurement of a confined aquifer using a pumping test. Determine the hydraulic conductivity of the permeable layer. Use Eq. (7.49). Thickness of the aquifer, H = 4.5 m Piezometric level and radial distance of the first observation well: h1 = 2.9 m; r1 = 17.8 m Piezometric level and radial distance of the second observation well: h2 = 1.8 m; r2 = 8.1 m Rate of discharge from pumping, q = 0.5 m3/min
The contour map in Figure 1 depicts porosity variation within a sandstone reservoir. The lines connect points of equal porosity. If reservoir is 10 miles long, 3 miles wide, 100 ft thick and Table 1 depicts the area and thickness. Analyze: a) An average porosity. b) the most possible average pore volume in barrel
The given values are as follows: The specimen's e=0.46 length of soil specimen=450mm constant head difference=700mm Water collected in 3 minutes =3.54x10-4 m3 Area=2.26x10-3 m2 1) Find the coefficient of permeability (Ans. 2.012 m/hr) 2) Find the discharge velocity (Ans. 0.052 m/min) 3) Find the interstitial velocity (Ans. 0.165 m/min)
A 8.81-pound sample is obtained from an excavation with a volume of 0.070 cubic feet. The sample weight 7.63 pounds after drying. Assume a specific gravity of 2.66. Calculate wet unit weight, dry unit weight, void ratio, porosity and degree of saturation.
Note) For soil sample in Table 2, initial thickness of sample = 14.31 mm, sample area = 2827.433 mm^2, dry weight measured at the end of test = 52.53 g, specific gravity = 2.7 Also, Determine the compression index and expansion index Please show graph
10 A clay layer having a thickness of 13.19 m. has an initial void ratio of 1.18. It is compressed and the void ratio changed to 0.88. Determine the reduction in thickness, in mm., of the clay layer. Round off to three decimal places. Input the numerical value only.
Determine the void ratio if porosity is 0.334
please help with following question: For all three samples listed, determine the following parameters: Dry Density rd, Saturated Density rsat, void ratio e, porosity n, D10, D60 & Uniformity Coefficient Uc,