A channel is (50) m wide, 2.5m deep and has a bed slope of 1 in 4000. Determine the bed load transported by the channel by Meyer-Peter's equations. take Manning's. The mean diameter of the material is 0.30mm and the representative size of the bed material for rippled bed is 0.50 mm (K)?

A channel is (50) m wide, 2.5m deep and has a bed slope of 1 in 4000. Determine the bed load transported by the channel by Meyer-Peter's equations. take Manning's. The mean diameter of the material is 0.30mm and the representative size of the bed material for rippled bed is 0.50 mm (K)?

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.2P

See similar textbooks

Related questions

Q: Que. If the average sewage from a city is 95 × 1061/day and the average 5 day BOD is 300mg/l against…

Q: OK, now we have to deal with the spoils. Assume the Finished Grade (FG) was level and all one…

A: Given Finished grade was level No slope Using minimum OSHA offset it is 2 Ft so…

Q: section of the bar shown in the Figure when The central section is 30 mm square cross-se on; their…

A: Force in each bar is same F=25,000Ntension

Q: uniaxial tension test is Fy (MPa). Based on the stress state against failure if all stresses are inc

A: von mises theory is theory of plasticity ,general stress matrix is σ1 τ12 τ13…

Q: 3= The state of strains at a point are defined as follows. Find X and Y such that the normal and…

Q: PROBLEM NO. 1: The simply supported beam has a length of 7.2 meters and carries a total service load…

A: Given Data:Length = 7.2mService load = 40.16kN/mfc=21MpaFy=420h=

Q: A horizontal reducing bend deflected at 110° has a diameter of 250mm upstream and 100mm downstream.…

A: Given Specific Gravity of fluid= 0.90

Q: Q4/ Determine the Moment of Inertia of the shaded area with respect to X axis, Ix, (all dimensions…

A: Note - I already solved this question So here uploading this answer with few changes.

Q: Q5: A 50m *30m site has 1 m thick layer of organic soil, to be replaced with granular fill (G=2.6)…

A: The proctor compaction test is the test carried out on the soil samples to arrive the maximum dry…

Q: A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the…

Q: Q.1) Determine the support reactions at A and the tension in the cable of the beam-pulley system…

Q: A vertical sag curve joins a -3.0% downgrade with a 2.0% upgrade. The Chainage at Vertical…

A: Given Data:g1=-3%g2=2.0%Chainage at vertical intersection point = 1100mreduced level = 122mchainage…

Q: Describe why the sightline for electronic distance measurement should be at least 0.5 m off the…

A: the sightline for electronic distance measurement should be at least 0.5 m off the surface of the…

Q: Determine the stress in each section of the bar shown in the Figure when subjected to an axial…

Q: What is a 'misfire'? Explain how you should manage a misfire, if it occurs?

A: Misfire means the complete or partial failure of a blasting charge to explode as planned. The…

Q: The beam shown in Fig. is made from two boards. Draw the shear stress at (A.B.C.D) to hold the…

A: Reaction calculation For equilibrium of static (i)∑ME = 0 (ccw +ve, cw -ve) (RE x 8) - [6.5 x 4 x…

Q: Q5: A 50m*30m site has 1 m thick layer of organic soil, to be replaced with granular fill (G-2.6)…

A: The given data is shown below: Size of site=50m×30mDepth=1mGs=2.6Fines=21%Oversized…

Q: A horizontal collimation test is performed on an automatic level following the procedures described…

A: Answer We are given Instrument set up at point 1 rod reading at A (ha) = 3.886 ft rod reading at B…

Q: Q1: If F-150 lb and @= 55, determine the magnitude and direction measured clockwise from the…

A: Resultant Force(FR)= 160.71 lb Angle(θ)= 38.34 degree

Q: of How Walue of deflection at Points Card D by using doubl use EI=Snstant. loo KN

Q: A factory uses carbonic acid in its industrial processes so that 90% by weight is used in industry…

A: Only 90% using efficiently, remaining 10% emitting to atmosphere.

Q: D. A compound curve with R1=390.32 m, R2=174.20 m has a central angle of 12° and 18°, respectively.…

Q: The roughness for all pipes is 0.02. Pipe Diameter Length (cm) (m) AJ 15 350 200 BJ 10 CJ 250 500 A…

Q: Where, X=36 A retaining wall (frictionless) is shown in a) Plot the variation of active and…

A: surcharge q = 1.5 x 36 = 18 kPa bulk density of sand γbulk= 17 kN/m3 total height of wall = 36 m…

Q: Q5/ Blocks of wood are glued together to form the shaded section shown in the figure. Find the…

Q: Determine and plot the tensions in cable segments AC and BC as a function of x over

Q: 6. The Parker truss is loaded as shown in Figure 1-104. Determine the forces in members BD, BE, CE,…

Q: In an effort to pay off the loan quickly, a borrower made four payments in years 1 through 4, with…

Q: For the given state of stress, 60 MPa 45 MPa (a) Draw Mohr's circle, label all key points on the…

Q: force between the cable and the pulley is negligible, determine W 100 kg 25° 3 10° Hs = 0.3 Mk = 0.2

Q: P2.2 The two bars shown in Figure P2.2 are used to support a load P. When unloaded, joint B has…

Q: The can in the given image floats in the position shown. The diameter of the can is 19 cm. What is…

A: Asked: To determine the weight of the can shown floating in the given figure. Given: Diameter of…

Q: The spacing of moving traffic in a queue can be modeled by s = 3.0 + 0.4u + 0.0025u2, where u is the…

Q: As described in the Data and Results part of , all tables and graphs must have descriptive…

A: Given:- The range of the mass is 50 kg to 120 kg The increments to be used = 10 kg To determine:-…

Q: Oil (SG=0.8) discharges from a 250mm diameter pipe through a sharp-crested orifice whose dia is…

Q: (4) The cross section of a given column is shown in the figure, b.-24cm, x-2.02cm, the angle for the…

A: Solution: Design of lacing: Lacing provided at 45o to horizontal: Horizontal spacing = bo + 2xo =…

Q: Example 2: Determine the force in each member of the truss. Assume the members are pin connected at…

Q: 58. What can be the phase inspections done by local authority while construction?

A: Brief concept introduction- Inspection- It is a process of careful examination. Inspection is a very…

Q: Calculate the size of drain at the outlet Given: Area of drainage system=50000m2 Manning (n)= 0.013…

A: given- Area of drainage system-A=50000 m2manning's coefficient n=0.013Drainage coeffcientDc=1.1…

Q: Compute the force in all members of the truss shown in Fig. T-08. 50 KN 30 KN MATHalino.com B 4 m 5…

Q: (c) Liquid flows through an orifice in the bottom of a cylindrical tank at a velocity of 4m/s. If…

Q: 3= The state of strains at a point are defined as follows. Find X and Y such that the normal and…

A: This question is related to the Strength of Material.

Q: 1-Where are shallow foundations most commonly used? 2-What are some benefits to shallow foundations?…

Q: To calibrate an EDM instrument, distance AC, AB, and BC along a straight line were observed as…

A: Given values, Line AC = 90.158 m Segments AB = 60.025 m and BC = 30.164

Q: 3= The state of strains at a point are defined as follows. Find X and Y such that the normal and…

Q: For the mechanism shown below, compute the magnitude of the force (F) required to break contact at…

A: Given, Spring constant(k) = 1800N/m S = 10mm Force required to break contact at point c=?

Q: 1- Consider the unit cube shown in the Figure, which undergoes the deformation: 1 x₁ =α (X₁- X₂), x₂…

Q: Q2/A/For what velocity of flow of water in a new, clean, 8-in diameter of cast iron pipe would an…

A: Solution: Given: hL = 7.7 m L = 430 m D = 8 in = 0.203 m Ch = 130 (Hazen - Williams coefficient for…

Q: Explain the target building performance levels and describe three performance levels in details

A: Target Building Performance Levels:- Building performance is the combination of performance of both…

Q: If the temperature and pressure at measurement time are 18°C and 760 mm Hg, respectively, what will…

A: An electronic measurement device shows the electrical values such as current, voltage frequency,…

Question

A channel is (50) m wide, 2.5m deep and has a bed slope of 1 in 4000.
Determine the bed load transported by the channel by Meyer-Peter's
equations. take Manning's. The mean diameter of the material is 0.30mm and
the representative size of the bed material for rippled bed is 0.50 mm (K)?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A deposit of cohesionless soil with a permeability of 0.3 mm/s has a depth of 12 m with impervious ledge below. A sheet pile wall is driven into this deposit to a depth of 8 m. The wall extendsabove the surface of the soil, and a 3 m depth of water acts on one side. Sketch the flow net and determine the seepage quantity. a. 600 ml/s/meter length b. 300 ml/s/meter length c. 1200 ml/s/meter length d. 900 ml/s/meter length
A deposit of cohesionless soil with a permeability of 0.3 mm/s has a depth of 12 m with impervious ledge below. A sheet pile wall is driven into this deposit to a depth of 8 m. The wall extendsabove the surface of the soil, and a 3 m depth of water acts on one side. Sketch the flow net and determine the seepage quantity. Provide a diagram a.600 ml/s/meter length b.300 ml/s/meter length c.900 ml/s/meter length d.1200 ml/s/meter length
A rectangular deck scow 35.0 m long, 5.60 m wide, and 3.50 m high has a draft of 1.30 m when light ad a draft of 2.95 m when loaded. The bottom length of the scow is 24.0 m. The waterline is 30.0 m long when the scow is loaded with rocks and 25.50m long when light. If sea water weighs 1026 kg/cum and the loaded dredged material weighs 3208 kg/cum, determine the following: a. volume of water displaced when unloaded of light b. displacement loaded c. weight of the water displaced by the load d. volume of the loaded rock
a) find the weight of concrete dam if it has a depth of eleven meters into the page. Where does the weight act (centroid)? b) if the water level is less than 4m, what are the horizontal and vertical load intensity diagrams and the equivalent point load (in cartesian form in terms of "h") for each? c) repeat b if the water level is greater than 4m.
A dam shown in figure has water 2.7 m high on the vertical upstream side. If unit weight of concrete is 23.5 kN/cu.m, determinea. Minimum width of the base that the resultant falls within the middle thirds. Neglect hyrostatic uplift.b. Minimum coefficient of friction to prevent sliding
A canal of trapezoidal section has bed width of 8 m and bed slope of 1 in 4000. If the depth of flow is 2.4 m and side slopes of the channel are 1 horizontal to 3 vertical, determine the average flow velocity and the discharge carried by the channel. Also compute the average shear stress at the channel boundary. Take value of Chezy’s Constant = 50
Use 10 kN/m3 for unit weight of water. For a concrete structure that retains water, a flow net is sketched as shown in Figure H8-3. Noting the marked location of the Datum, answer the following: Mark on the figure all boundary Also mark the type of each boundary. Calculate the uplift pressures at points A, B, C, D, E, and F. Calculate the factor of safety against The seepage loss (q) per day per meter length of the (i.e. q in m3/day/m) if the permeability of the soil is k = 10-4 m/sec.
An embankment consists of clay fill for which c=25 kPa and angle of internal friction is 260 9from consolidated undrained test with pore pressure measurement) The weight of fill per unit volume is 18.64 kN/m3. Compute the stress in kPa at depth of 20 m. Show free body diagram a.21.6 b.372.8 c.192.8 d.62.5
A concrete dam retaining water is shown below, if the specific weight of concrete is 23.5 KN/m, find the factor of safety against sliding, the factor of safety against overturning, and the pressure intensity on the base. coefficient of friction between dam and foundation soil is 0.45 ? (y water 9.8 KN/m').
A single anchor slab is shown in Figure P14.12. Here, H = 0.9 m, h = 0.3 m, γ = 17 kN/m3, and Φ' = 32º. Calculate the ultimate holding capacity of the anchor slab if the width B is (a) 0.3 m, (b) 0.6 m, and (c) = 0.9 m.
A 10 m clay stratum is overlaying a rock stratum. If water table is at the ground surface, calculate the overburden soil pressure at the middle of the clay layer using the ff. properties of clay: ∂sat = 17.95 kn/m3, e = 1.1 , LL = 60%
Assume some demand rates in the hydraulic network analysis. Explain briefly