One simple, though impractical, way to generate electrical power is shown below. A bar of metal with negligible resistance is in friction-less contact with two wires (also negligible resistance) spaced 15 cm apart. The changing magnetic flux generates an emf in the loop shown below. Zero-resistance wires Push 0.4 m/s 0.75 T First, what is the emf around this loop in mV to 2 significant digits?

One simple, though impractical, way to generate electrical power is shown below. A bar of metal with negligible resistance is in friction-less contact with two wires (also negligible resistance) spaced 15 cm apart. The changing magnetic flux generates an emf in the loop shown below. Zero-resistance wires Push 0.4 m/s 0.75 T First, what is the emf around this loop in mV to 2 significant digits?

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter14: Inductance

Section: Chapter Questions

Problem 75AP: A small, rectangular single loop of wire with dimensions 1, and a is placed, as shown in the plan of...

See similar textbooks

Similar questions

The current in the long, straight wire shown in the accompanying figure is given by, where I=I0sint I0=15Aand=120rad/s. What is she current induced in the rectangular loop at (a) t = 0 and (b) t=2.1103s The resistance of loop is 2.0 .
The conducting rod shown in the accompanying figure moves along parallel metal rails that are 25-cm apart. The system is in a uniform magnetic field of strength 0.75 T, which is directed into the page. The resistances of the rod and the rails are negligible, but the section PQ has a resistance of 0.25 . (a) What is the emf (including its sense) induced in the rod when it is moving to tire right with a speed of 5.0 m/s? (b) What force is required to keep the rod moving at this speed? (c) What is the rate at which work is done by this force? (d) What is the power dissipated in the resistor?
The normal to tt plane of a single-turn conducting loop is directed at an angle to a spatially uniform magnetic field B. It has a fixed area and orientation relative to the magnetic fleck Show that the emf induced In the loop is given by i = (dB/dt)(Acos),where A is the area of the loop.
In the circuit sho in the accompanying figure, the rtd slides along the conducting rails at a constant VelOCity v. The velocity is in the same plane as the rails and directed at an angle 6 to them. A uniform magnetic field Bis directed out of the page. What is the emf induced in the r?
The potential difference V(t) between parallel plates shown above is instantaneously increasing at a rate of 107V/s. What is the displacement current between the plates if the separation of the plates is 1.00 cm and they have an area of 0.200m2?
A small, rectangular single loop of wire with dimensions 1, and a is placed, as shown in the plan of a much larger, rectangular single loop of wire. The two short sides of the larger loop axe so far from the smaller loop that their magnetic fields over the smaller fields over the smaller loop can be ignored. What is the mutual inductance of the two loops?
Two long, parallel wires cy equal currents in opposite directions. The radius of each wire is a, and the distance between the centers of the wires is d, Show that if the magnetic flux within the wires themselves can be ignored, the self-inductance of a length 1 of such a pair of wires is L 0 l in d1 a (Hint Calculate the magnetic flux through a rectangle of length 1 between the wires and then use L=N/I
Suppose a conducting rod is 87 cm long and slides on a pair of rails at 2.5 m/s. What is the strength of the magnetic field in T if a 1 V emf is induced?
An alternator is an AC generator, so from there, we are given a car alternator which produces about 14 V peak output to charge the car's 12-V battery. If an alternator coil is 17 cm in diameter is spinning at 1200 revolutions per minute in a 0.19T magnetic field, how many turns must it have to produced a 14V peak output? I am unfamiliar with the derivations, so need someoone who can help me with understandig symbology to the values better.
Here you see a single loop of stiff wire, 10.0 cm on a side, immersed in a magnetic field of 0.225 T. Suppose that you remove the loop from the field in just 0.00208 sec. What emf or voltage will be induced in the loop? Express your answer to three significant figures and in normal notation.
There is a circular conducting loop with diameter = 8 cm that has 400 turns that is placed in a magnetic field directed into the plane. Magnetic field increases from 0.4 T to 1.2T in 2.4 sec. -what's the induced emf (answers in volts) on loop -what's the magnitude of induced current (mA), if total resistance of the loop =2Ω?
The plane of a square coil of wire is perpendicular to the direction of a magnetic field. The coil has N turns, a length and width of L, and a total resistance of R. Show how to find an equation for the rate of change of B needed to produce some current, I. (Find ?̇ as a functionof the variables given)