onsider an aluminum pan used to cook stew on top of an electric r nd' has a diamețer of 14 cm. The electric heating unit on the range percent of the heat generated in the heating element is transferred of the jhner surface of the pan is measured to be 108°C.

onsider an aluminum pan used to cook stew on top of an electric r nd' has a diamețer of 14 cm. The electric heating unit on the range percent of the heat generated in the heating element is transferred of the jhner surface of the pan is measured to be 108°C.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.19P: 1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the...

See similar textbooks

Similar questions

Heat is transferred at a rate of 0.1 kW through glass wool insulation (density=100kg/m3) with a 5-cm thickness and 2-m2 area. If the hot surface is at 70C, determine the temperature of the cooler surface.
2.55 A long, 1-cm-diameter electric copper cable is embedded in the center of a 25-cm-square concrete block. If the outside temperature of the concrete is 25oC and the rate of electrical energy dissipation in the cable is 150 W per meter length, determine temperatures at the outer surface and at the center of the cable.
A cooling system is to be designed for a food storage warehouse for keeping perishable foods cool prior to transportation to grocery stores. The warehouse has an effective surface area of 1860 m2 exposed to an ambient air temperature of 32C. The warehouse wall insulation (k=0.17W/(mK)) is 7.5 cm thick. Determine the rate at which heat must be removed (W) from the warehouse to maintain the food at 4C.
8.15 A mercury bath at is to be heated by immersing cylindrical electric heating rods, each 20 cm tall and 2 cm in diameter. Calculate the maximum electric power rating of a typical rod if its maximum surface temperature is .
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
A 0.3-cm-thick, 12-cm-high, and 18-cm-long circuit board houses 80 closely spaced logic chips on one side,each dissipating 0.06 W. The board is impregnated with copper fillings and has an effective thermalconductivity of 16 W/m · °C. All the heat generated in the chips is conducted across the circuit board andis dissipated from the back side of the board to the ambient air at 30°C, which is forced to flow over thesurface by a fan at a free-stream velocity of 400 m/min. Determine the temperatures on the two sides ofthe circuit board.
Consider a 1.2-m-high and 2-m-wide glass windowwith a thickness of 6 mm, thermal conductivity k = 0.78W/m·K, and emissivity « = 0.9. The room and the wallsthat face the window are maintained at 25°C, and the averagetemperature of the inner surface of the window is measuredto be 5°C. If the temperature of the outdoors is 25°C,determine (a) the convection heat transfer coefficient on theinner surface of the window, (b) the rate of total heat transferthrough the window, and (c) the combined natural convectionand radiation heat transfer coefficient on the outer surface ofthe window. Is it reasonable to neglect the thermal resistanceof the glass in this case?
The roof of a house is electrically heated. This roof is 6 m long, 8 m highwide and 0.25 m thick, and is made with a flat layer of concrete whose conductivityis ? = 0.8 ?⁄? ?. The temperatures of the inner and outer surfaces are15 and 4 °C, respectively, for a period of 10 hrs. Determine a) the reason for the lossof heat through the roof that night and b) the cost of that heat loss to the homeownerof the house, if the cost of electricity is $0.08/kWh.
Consider a 15-cm * 20-cm printed circuit board (PCB) that has electronic components on one side. The board is placed in a room at 20°C. The heat loss from the back surface of the board is negligible. If the circuit board is dissipating 8 W of power in steady operation, determine the average temperature of the hot surface of the board, assuming the board is (a) vertical, (b) horizontal with hot surface facing up, and (c) horizontal with hot surface facing down. Take the emissivity of the surface of the board to be 0.8 and assume the surrounding surfaces to be at the same temperature as the air in the room. Evaluate air properties at a film temperature of 32.5°C and 1 atm pressure. Is this a good assumption?
A person puts a few apples into the freezer at 15°C cool them quickly for guestswho are about to arrive. Initially, the apples are at a uniform temperature of 20°C,and the heat transfer coefficient on the surfaces is 8 W/m2·K. Treating the apples as9-cm-diameter spheres and taking their properties to be 840 kg/m3, Cp 3.81 kJ/kg·K, k = 0.418 W/m·K, and α =10-7 m2/s, determine the center and surface temperatures of the apples in 1 h. Also, determine the amount of heat transfer from each apple. Solve this problem using analytical one-term approximation method (notthe Heisler charts). Answer: Center: 11.2 ℃, Surface: 2.7 ℃, heat transfer: 17.2 kJ
Consider a 2-m-high electric hot-water heater thathas a diameter of 40 cm and maintains the hot water at 55°C.The tank is located in a small room whose average temperatureis 27°C, and the heat transfer coefficients on the innerand outer surfaces of the heater are 50 and 12 W/m2·K,respectively. The tank is placed in another 46-cm-diametersheet metal tank of negligible thickness, and the spacebetween the two tanks is filled with foam insulation (k =0.03 W/m·K). The thermal resistances of the water tank andthe outer thin sheet metal shell are very small and can be neglected. The price of electricity is $0.08/kWh, and the home owner pays $280 a year for water heating. Determine the fraction of the hot-water energy cost of this household that is due to the heat loss from the tank. Hot-water tank insulation kits consisting of 3-cm-thick fiberglass insulation (k = 0.035 W/m·K) large enough to wrap the entire tank are available in the market for about $30. If such an insulation is installed on…
Consider a sealed 20-cm-high electronic box whose base dimensions are 40 cm x 40 cm placed in a vacuum chamber. The emissivity of the outer surface of the box is 0.95. If the electronic components in the box dissipate a total of 100 W of power and the outer surface temperature of the box is not to exceed 55°C, determine the temperature at which the surrounding surfaces must be kept if this box is to be cooled by radiation alone. Assume the heat transfer from the bottom surface of the box to the stand to be negligible.