onsider the combination of resistors shown in the figure below. 120 4.0 0 5.0 N 6.0 N 8.0 N (a) Calculate the equivalent resistance (in N) between points a and b. Ω (b) If a voltage of 45.2 V is applied between points a and b, find the current (in A) in each resistor. 12 Q A 6.0 N 5.0 0 A 4.0 N A 8.0 0 A

onsider the combination of resistors shown in the figure below. 120 4.0 0 5.0 N 6.0 N 8.0 N (a) Calculate the equivalent resistance (in N) between points a and b. Ω (b) If a voltage of 45.2 V is applied between points a and b, find the current (in A) in each resistor. 12 Q A 6.0 N 5.0 0 A 4.0 N A 8.0 0 A

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter18: Direct-Current Circuits

Section: Chapter Questions

Problem 11P: Consider the circuit shown in Figure P18.11. Find (a) the potential difference between points a and...

See similar textbooks

Similar questions

Consider the circuit shown in Figure P18.10. (a) Calculate the equivalent resistance of the 10.0- and 5.00- resistors connected in parallel. (b) Using the result of part (a), calculate the combined resistance of the 10.0-, 5.00-, and 4.00- resistors. (c) Calculate the equivalent resistance of the combined resistance found in part (b) and the parallel 3.00- resistor. (d) Combine the equivalent resistance found in part (c) with the 2.00- resistor. (e) Calculate the total current in the circuit. (f) What is the voltage drop across the 2.00- resistor? (g) Subtracting the result of part (f) from the battery voltage, find the voltage across the 3.00- resistor. (h) Calculate the current in the 3.00- resistor. Figure P18.10
Would your headlights dim when you start your car's engine if the wires in your automobile were superconductors? (Do not neglect the battery’s internal resistance.) Explain.
Consider the circuits shown below, (a) What is the current through each resistor in part (a)? (b) What is the current through each resistor in part (b)? (c) What is the power dissipated or consumed by each circuit? (d) What is the power supplied to each circuit?
Referring to the example combining series and parallel circuits and Figure 21.6, calculate I3in the following two different ways: (a) from the known values of I and I2 ; (b) using Ohm’s law for R3. In both parts explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors.
The label or a portable radio recommends the use of rechargeable nickel-cadmium cells (nicads), although they have a 1.25-V emf while alkaline cells have a 1.58-V emf. The radio has a 3.20- resistance, (a) Draw a circuit diagram ot the radio and its batteries. Now, calculate the power delivered to the radio, (b) When using Nicad cells each having an internal resistance of 0.0400O. (c) When using alkaline cells each having an internal resistance of 0.200 . (d) Does this difference seem significant, considering that the radio s effective resistance is lowered when its volume is turned up?
A 12-V battery is connected across a device with variable resistance. As the resistance of the device increases, determine whether the following quantities increase, decrease, or remain unchanged. Indicate your answers with I, D, or U, respectively. (a) The current through the device. (b) The voltage across the device. (c) The power consumed by the device.
The following statements are related to household circuits and electrical safety. Determine whether each statement is true (T) or false (F). (a) Circuit breakers are wired in series with the outlets they protect. (b) A circuit breaker rated at 20 A provides a constant current of 20 A to each outlet in the circuit. (c) Three-wire electrical cords help prevent dangerous electrical shocks by grounding the case of a device.
Unreasonable Results A 1.58-V alkaline cell with a 0.200- internal resistance is supplying 8.50 A to a load, {a) What is its terminal voltage? (b) What is the value of the load resistance? (c) What is unreasonable about these results? (d) Which assumptions are unreasonable or inconsistent?
You have a faculty position at a community college and are m (caching a class in automotive technology. You are deep in a discussion of using jumper cables to start a car with a dead battery from a car with a fresh battery. You have drawn the circuit diagram in Figure P27.16 to explain the process. The battery on the left is the live batten- in the correctly functioning car, with emf and internal resistance RL where the L. subscript refers to live. Its terminals are connected directly across those of the dead battery, in the middle of the diagram, with emf and internal resistance RD where the D subscript refers to "dead Then, the starter in the car with the dead battery is activated by closing the ignition switch, allowing the car to start. The resistance of the starter is Rs. A student raises his hand and asks, So is the dead battery being charged while the starter is operating? How do you respond?
A 12.00-V battery has an internal resistance of a tenth of an ohm. (a) What is the current if the battery terminals are momentarily shorted together? (b) What is the terminal voltage if the battery delivers 0.25 amps to a circuit?
Construe! Your Own Problem Consider a rechargeable lithium cell that is to be used to power a camcorder. Construct a problem in which you calculate the internal resistance of the cell during normal operation. Also, calculate the minimum voltage output of a battery charger to be used to recharge your lithium cell. Among the things to be considered are the emf and useful terminal voltage of a lithium cell and the current it should be able to supply to a camcorder.
Suppose you are doing a physics lab that asks you to put a resistor into a circuit, but all the resistors supplied have a larger resistance than the requested value. How would you connect the available resistances to attempt to get the smaller value asked for?