Operational Amplifier (Op-Amp) is a solid-state device with voltage amplification capabilities as shown in Figure Q1. (a) Name the function of Op-Amp U1, U2 and U3 in Figure Q1. (b) Derive the output voltage (Vol, Voz and Vo3) of each Op-Amp in Figure Q1. Based on derivation in Q1(b), calculate the output voltages (Vol, Vo2 and Vo3) of the circuit. All the Op-Amps are powered with + 12V voltage supplies. Given: Ra = Rb = 1 kN, Ry = Rx = 10 kN, Ra = 3.6 kN, Rr = 3 k2. The input voltages: V,= V = 5 V. (c) (d) Draw and label clearly the sinusoidal output of Vol, Vo2 and Vo3.

Operational Amplifier (Op-Amp) is a solid-state device with voltage amplification capabilities as shown in Figure Q1. (a) Name the function of Op-Amp U1, U2 and U3 in Figure Q1. (b) Derive the output voltage (Vol, Voz and Vo3) of each Op-Amp in Figure Q1. Based on derivation in Q1(b), calculate the output voltages (Vol, Vo2 and Vo3) of the circuit. All the Op-Amps are powered with + 12V voltage supplies. Given: Ra = Rb = 1 kN, Ry = Rx = 10 kN, Ra = 3.6 kN, Rr = 3 k2. The input voltages: V,= V = 5 V. (c) (d) Draw and label clearly the sinusoidal output of Vol, Vo2 and Vo3.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Answer the following questions a) What assumption do we make for an ideal op - amp? b) Explain what slew rate is why it is important characteristic for an op amp.
Q 1) For the given circuit shown in Figure 4.1: (i) Provide the name for this op-amp circuit configuration and use the ideal op-amp assumptions to solve for the output voltage in terms of the input voltages and resistors. (ii) What is the input resistance seen by ?0, V1 and V2. ?
Explain how to use virtual ground concept in the analysis of op-amps.
An inverting op – amplifier stage is designed with an input resistance of 5 KΩ and feedback resistance of 10 KΩ. The load resistance is 100 Ω with DC gain of 5x10^4 . The output internal resistance is 500 Ω while the input impedance is infinity, assuming an input voltage of 1.5 volts, calculate the following ?a) The AC gain ?b) The output voltage ?c) The looking back resistance ?
Why is there a difference between the theoretical and practical values of voltage gain in an inverting and non-inverting Op amplifier?
Draw and interpret the gain-frequency graph of the op-amp circuit given in the figure.
Give the characteristics of ideal op-amp.
How do we increase the voltage gain of an inverting and non-inverting op amp amplifier?
1. Assuming the op amp to be ideal, derive an expression for the closed-loop gain of the circuit shown in Figure 1.
Figure Q2(a) shows an amplifier system with the given input voltagewaveform Vin and the corresponding output voltage waveform Vout. If a practical op-amp is used in the amplifier system in Figure Q2(a),calculate the closed-loop gain, ACL given that the open-loop gain, AOL =3000. You can use the value of resistances found in Q2(a)(i).
What must the voltage at the inverting input of the op-amp be? What is the voltage drop across Rin? What is the input current, iin, through Rin? What is the output voltage vout?
Explain with the help of proper diagram and necessary derivation, How Op-Amp can be used as inverting , noninverting and difference amplifier. Assume open loop configuration.