"Order" of the following control system is

Q: The is known as the final control element . -

A: The final element in the control system is that element which is responsible or the output of the…

Q: In |type of control system, controller gets the sampled error signal.

A: This is the question based on control syatem subject . In this the error sampled signal is present…

Q: For the closed-loop control system described by the block diagram shown in figure below. determine…

A:

Q: b- Fill in the blanks (Answer Two Only) 1- Give an application of three phase AC voltage controller.…

A:

Q: Which of the following is the Type of the control system given below?

A:

Q: . Design a traffic light controller where; frequeny = 0.5 Hz, red light oposed to be ON for 10 Sec.,…

A: The code for this traffic light mild controller is easy and smooth to understand. we've exhibited…

Q: Determine in which part is the Power Control Circuit and Control Center.

A: A circuit diagram is given in the question. In the given schematic we need to determine which part…

Q: Define controllability in the control system.

A: Controllability in the control system define that all the state variables are input dependent. It is…

Q: In short tell the difference in the stepper and servo motor.

A: The difference in the Stepper and Servo motor: The difference in the Stepper and Servo motor: The…

Q: A washing machine is supplied with hot and cold water from two different supplies. Draw the bock the…

A: Given, Two inputs with cold and hot water supply. The flow of hot water as well as the cold water…

Q: Control Systems

A: According to question: The phase cross over frequency is calculated as

Q: The regulation of a 250-volt shunt generator is 6 per cent. Calculate the no-load voltage

A:

Q: Using the following control devices ,draw an electrical circuit that will manage  the direction of…

A: Given circuit-

Q: 4 For the closed-loop control system described by the block diagram shown in figure below. determine…

A:

Q: In closed loop control system, that the system is unstable C the output has an effect upon the…

A:

Q: the Starting Up the Power Station Simulator Give a n example of faults that require giving a signal…

A:

Q: A closed-loop temperature control system has the ability to automatically maintain the temperature…

A: True

Q: (B)-Draw a neat diagram to show potential divider arrangement of rheostatic control speed for d.c.…

A: Potential divider arrangement of rheostatic control speed for D.C. shunt motors: Rf Field…

Q: For shunt generator which kind of apparatus is used for adjusting the voltage

A: For shunt generator, the potentiometer is used for adjusting the voltage. It controls the field of…

Q: b) Show the values of all eight control signals shown in Fig 4.15.

A: Given: To find the values of all eight control signals using the given diagram:

Q: cus for the following control system s.

A: Root locus is the locus of roots of characteristics equation when gain parameter is varied from zero…

Q: A single - break control is a?

A: A single- break control is a standard-duty selector switch.

Q: It is the most commonly used stepper motor driver which is directly connected to the PC.

A: The most commonly used stepper motor driver which is connected to the pc is " ULN2003".

Q: What is the most common voltage usted for control system

A: There are two basic components which are used in the most common voltage for the control system; 1.…

Q: Explain the difference between load and auxiliary contacts.

A: Auxiliary contacts are small. These are used as part of control circuit .

Q: For the closed-loop control system described by the block diagram shown in figure below. determine…

A:

Q: For the closed-loop control system described by the block diagram shown in figure below. determine…

A:

Q: For the closed-loop control system described by the block diagram shown in figure below. determine…

A: In the control system, What is value of K1 and K2? If damping ratio= 0.515 and damping frequency =…

Q: Compare between the status and control flags? Explain the status flags for the operation AEH+37H

A: Status flag show the status of the microprocessor accumulator after an arithmetic or logical…

Q: What is the modus operandi motion control lamp Please not handwriting

A: the modus operandi motion control lamp

Q: Compare between indirect and direct control circuits.

A: Indirect control circuit : Cylinders with large piston diameter have a high air requirement. Control…

Q: In type of control system, control signal is applied continuously through continuous feedback.

A:

Q: In case of open loop control system, choose correct option. (1). Generally unstable. (2). Unreliable…

A: Control system: The output quantity is controlled by varying input quantity is called as control…

Q: The ____ is an example of equipment that is operated by an automatic control system.

A: Given Data: The ____ is an example of equipment that is operated by an automatic control system.

Q: For the closed-loop control system described by the block diagram shown in figure below. determine…

A:

Q: Which among the following represents the closed-loop system? I. Television remote control II.…

A: We need to select system which have feedback system

Q: Construct the Routh array for this control system. What is the entry on the third row of the first…

A:

Q: 5. Fast help needed to answer this Engineeing question. Check image. Postive feedback for right…

A:

Q: How Get = S+2 Rind the first order in control system and draw

A: Important Notes about first order system  First order system can be described by first order…

Q: Design a labelled motor control circuit with an accompanying power circuit to operate 3 asynchronous…

A: Asynchronous motor- Asynchronous motor is also called as induction motor. It is define as an AC…

Q: For the closed-loop control system described by the block diagram shown in figure below. determine…

A:

Q: Differentiate the used of Stepper motor over Servo Motor as applied for DC Source.

A: A stepper motor is to boot a digitally stepped motor, it takes a sequence of pulses to form it take…

Q: Sump pumps and fill tanks have different wiring requirements for control components.

A: Control components are those components that can regulate a device or electrical components .…

Q: Explain in detail the control systems with the help of a block diagram.

A: Control system works on three block parameters 1) Plant transfer function 2) Controller 3)Feedback…

Q: 5) A Solid State Relay (SSR) can or should be used over a mechanical relay wher a) No mechanical…

A: A solid state relay is preferred over mechanical relay because of following reasons :- (a) the solid…

Q: Which of these two controllers can automatically adjust for changes in load? OA OB am-am Both of…

A: Controller: Controller is the fundamental part of controlling engineering. A controller is a…

Q: IV. Analysis 12V 9V 7.5V 6V 4.5V 3V. OV- Selector Switch 2 Poles/6 Position ✈ 00 2 3 LED's B+=? 1.…

A: Selector Switch : It is a switch that selects the desired port remaining other inactive by ohm's law…

Q: control systems

A:

Q: Question 79 Explain what are the positives and negatives of each of the controllers below: a)…

A: Positive of proportional controller : Very easy to implement  Steady state error is reduced due to…