oxygen make up the products of combustion and have a specific heat ratio k = 1.14 and a gas constant R = 383 J/kg-k. The nozzle has an exit to throat area ratio of Ae / Ath = 34.34 and has an exit diameter of 1.3 meters. Calculate the following: (a) Mass flow rate m for choked flow (b) Critical Mach numbers (c) Critical pressures

oxygen make up the products of combustion and have a specific heat ratio k = 1.14 and a gas constant R = 383 J/kg-k. The nozzle has an exit to throat area ratio of Ae / Ath = 34.34 and has an exit diameter of 1.3 meters. Calculate the following: (a) Mass flow rate m for choked flow (b) Critical Mach numbers (c) Critical pressures

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air enters a turbine at temperature and pressure of 800°C, 10bar respectively. The actual exit airtemperature is 180°C. The turbine isentropic efficiency is estimated to be 85%. Calculate the turbine exit pressure and the actual expansion index (n).
Explain the nozzle efficiency and its significance.
Give the design formulae of a dry liner in an internal combustion engine.?
Combustion gases with k=1.35, Cp =1107 J/(kg.K) and R= 287 J/(kg.K) flow at stagnation pressure and stagnation temperature of 390kPa and 1150 K respectively, flow through a 90o IFR turbine to an exit static pressure of 100 kPa. The total to static efficiency is 80% and the flow leaves the stator choked (Mach Number=1). The relative velocity at the inlet to the rotor is radial and the flow leaves the turbine without a swirl. Find (a) the work delivered per unit flow rate, (b) the impeller tip velocity and (c) the flow angle at the inlet to the rotor.
The pressure and temperature at the beginning of compression of a cold air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 7.2 MPa and the temperature is 2250 K. Assume constant specific heats evaluated at 300 K. Determine the mean effective pressure, in kPa.
How to calculate the static pressure and the stagnation pressure?
Steam expands in a steam turbine isentropically from intet to exhaust having an enthalpy drop=1200 kJ/kg. Assuming ideal conditions determine the mean diameter of wheel if the turbine were of: (1) Single impulse stage. (i) Single 50% reabron stage.
At the beginning of the compression process of air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and the mass flow rate in the system is 1900 kg/hr. Cp= 1.006 kJ/kg K Cv= 0.717 kJ/kg K 1) which figure represents the diagram for the process 2) which formula should be used to determine the temperature after compression? 3) calculate the temperature after isentropic compression in the presentable unit 4)which formula should be used to determine the temperature after heating? 5) calculate the temperature after isentropic compression in the presentable unit? 6) calculate the temperature after isentropic expansion in the presentable unit? 7) calculate the pressure after compression in kPa ? 8) which formula should be used to determine the work output of the engine? 9) calculate the work output of the engine kW? 10) calculate the thermal efficiency of the cycle in %? 11) which…
Air enters the compressor of an ideal air-standard Brayton cycle at 80 kPa, 299 K, with a volumetric flow rate of 6.1 m3/s. The compressor pressure ratio is 7. The turbine inlet temperature is 1886 K. Adopting the cold air-standard assumption, calculate: the mass flow rate of air to 3 d.p. in SI unit and privide unit symbol. Take the gas constant as 289 J/kg.K
Non-isentropic flow regime in the converging-diverging nozzle is restricted between chocking and exit shock conditions 1-True or 2-flase ??
please provide fast answer Steam issues from the nozzle of a single-impulse turbine at 800 m/sec on to blades moving at 300 m/sec. The blade tip angles at inlet and outlet are 36º each. The steam is to enter the blades without shock and the flow over the blades is frictionless. Determine— (a) the angle at which the nozzles are inclined to the motion of the blades; (b) diagram efficiency.
The pressure and temperature at the beginning of compression of a cold air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 7.2 MPa and the temperature is 2050 K. Assume constant specific heats evaluated at 300 K.Determine:(a) the compression ratio.(b) the cutoff ratio.(c) the percent thermal efficiency of the cycle.(d) the mean effective pressure, in kPa.