P=P sin aytCMSwwPROBLEM 19.147A machine element is supported by springs and is connected to a dashpot asshown. Show that if a periodic force of magnitude P=P sin w,t is applied to theelement, the amplitude of the fluctuating force transmitted to the foundation is1+ [²( * )(*) ³²√_@T+PETFm=Pm

Answered: Image /qna-images/answer/44ef596c-a9a1-4b23-aaa7-5d873c1a1042.jpg

Answered: P= P_ sin ayt MWS C ww PROBLEM 19.147 A…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the steady-state amplitude of the mass center of the bar of Fig P6.3 when its right end is subject to a moment M=4000sin105t N.m. Expected answer X=0.988mm
A reciprocating pump, of mass 68.6 kg, is mounted at the middle of a steel plate of thickness 0.8 cm, width 50.4 cm, and length 279 cm, clamped along two edges as shown in the accompanying figure. During operation of the pump, the plate is subjected to a harmonic force F(t)=301 cos(84.60t) N. Find the amplitude of vibration of the plate. Given that the equivalent stiffness of the plate can be calculated as k=192EI / l^3and the young modulus is E=200 GPa.
A mass of 36.3 kg is carried on an elastic system of stiffness 350 kN/m, and carries an absorber consisting of a mass 3.18 kg attached to it by a spring of stiffness 1 kN/m. Write down the equations of motion of the compound system and solve them to find the natural frequencies of the system and the corresponding amplitude ratios. [7.37 Hz; (X2/X1)= 39.8; 15.83 Hz; (X₂/X₁)= -0.2]
A 91-kg machine element supported by four springs, each of constant k = 175 N/m, is subjected to a periodic force of frequency 0.8 Hz and amplitude 89 N. Determine the amplitude of the fluctuating force transmitted to the foundation if (a ) a dashpot with a coefficient of damping c=365 N.s/m is connected to the machine element and to the ground, (b) the dashpot is removed.
A spring-mass system with m = 10 kg and k = 5000 N/m is subjected to a harmonic force of amplitude 250 N and frequency If the maximum amplitude of the mass is observed to be 100 mm, find the value of ?. Answer with interpretation
Two questions in one, see pictures below The assembly shown below with M8x1.25 bolt/nut is subjected to an oscillating force F that changes between 0 and Fmax. Obtain the Fmax (in kN) with a saftey factor of 3, such that the amplitude of the alternating stress on the threaded section of the bolt does not exceed 47 MPa. Assume that the bolt and nut were preloaded sufficiently. The stiffness of the clamped material is evaluated as 1,001 MN/m and the stiffness of the bolt is calculated as 343 MN/m.
400 kg machine is placed at the mid span of a 3.2 m simply supported steel beam (E=200\times10^9~N/m2) The machine is observed to vibrate with a natural frequency of 9.3 Hz. What is the size of the beam's cross section if the height is twice as the width, considering that:
The measurements on a mechanical vibrating system show that it has a mass of 8 kg and that the springs can be combined to give an equivalent spring of stiffness 5.4 N/mm. If the vibrating system have a dashpot attached which exerts a force of 40 N when the mass has a velocity of 1 m/s, find : 1. critical damping coefficient, 2. damping factor, 3. logarithmic decrement, and 4. ratio of two consecutive amplitudes.
QUESTION 2 The system shown in the figure consists of two bodies and three springs that may be set into free vertical vibration. Determine the natural frequencies of vibration for this system and compare the amplitudes of the movements of mass 1 and mass 2 for each f requency. M1=85kg, M2=150kg, k1= 70 kN/m, k2=55kN/m, k3=40kN/m. NB: Draw a detailed free body diagram for each mass to solve the problem . [27]
The assembly shown below with M8x1.25 bolt/nut is subjected to an oscillating force F that changes between 0 and Fmax. Obtain the Fmax (in kN) with a saftey factor of 2, such that the amplitude of the alternating stress on the threaded section of the bolt does not exceed 48 MPa. Assume that the bolt and nut were preloaded sufficiently. The stiffness of the clamped material is evaluated as 1,017 MN/m and the stiffness of the bolt is calculated as 346 MN/m.
Show that for a small value of the damping factor c/cc , the maximum amplitude of a forced vibration occurs when Wf= Wn and that the corresponding value of the magnification factor is ½ (c/c2).
Determine the natural frequencies and mode shapes of the system of Fig. P5.10 if k=12,000 N/m and each bar is of mass 12 kg and length 4m.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS