P В a Determine the normal stress due to force P at point A. Express your answer in units of MPa with one decimal place of accuracy. Compressive stress should be entered as negative and tensile stress should be positive. OA = MPa Determine the normal stress due to force P at point B. Express your answer in units of MPa with one decimal place of accuracy. Compressive stress should be entered as negative and tensile stress should be positive. OB = MPa Determine the resultant compressive force acting in the bracket at cut ABD due to the compressive normal stress. Express your answer in units of kN with one decimal place of accuracy. R = kN Check

P В a Determine the normal stress due to force P at point A. Express your answer in units of MPa with one decimal place of accuracy. Compressive stress should be entered as negative and tensile stress should be positive. OA = MPa Determine the normal stress due to force P at point B. Express your answer in units of MPa with one decimal place of accuracy. Compressive stress should be entered as negative and tensile stress should be positive. OB = MPa Determine the resultant compressive force acting in the bracket at cut ABD due to the compressive normal stress. Express your answer in units of kN with one decimal place of accuracy. R = kN Check

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the deformation ( in inches) of the steel rod shown under the given loads if P = 69698 lbQ = 35952 lb, R = 20650 lb, and E = 29 x 106 psi. Express your answer in four decimal places.
As shown in the figure, a hole is to be punched out of a plate having a shearing strength of s = 38.95 ksi. The compressive stress in the punch is limited to c = 58.44 ksi. If the plate is t = 0.25 inch thick, determine the diameter (in inches) of the smallest hole that can be punched. Round off the final answer to three decimal places.
The two vertical rods attached to the light rigid bar in the figure are identical except for length. Before the load W was attached, the bar was horizontal and the rods were stress-free. Determine the load in each rod if W = 6600 lb. (Determine load for rod A & B in lbs)
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 6 (Example: 4QT mm2 = 406 mm2). Just substitute the number in letter. Thank you! A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 4QT mm2. Determine the average axial stress in each bar.
Determine the compressive force (in lb) in the bars shown after a temperature rise of 173°F if d = 0.015 in. Round off the final answer to five decimal places. Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.78 sq. in E = 14959726 psi E = 10594540 psi L = 12.5 in L = 16.6 in α = 11.61 x 10-6/ °F α = 12.67 x 10-6/°F
If the allowable tensile unit stress on the gross area of a threaded steel bar is 14,500 psi, what is the required diameter of a bar, expressed as a multiple of 1/8 in., that will safely resist a total pull of 29,500 lb?A. 1 1/2 B. 1 5/8 C. 1 7/8 D. 2 1/8
Shear force and bending moment values acting on the section are given in Table 1. to yourselfMark the values (paying attention to the sign) on the section. Using these values, the bending stress andCalculate shear stress values and draw stress diagrams next to the section.Note: Draw the Bending (Normal Stress) diagram and Shear stress diagrams separately andShow the values you found on them. In this question, you can do unit conversions and use kg and cm. T= 17t M=15t/m b=45mm h=420mm t=60mm
. Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circular bars, one of brass and the other of steel, are to be loaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in'the two materials must not exceed 50 MN/m 2 and 100 MN/m z respectively. [27.6, 19.5, 19.5, 13.8 ram.] Can you please show a full solution explaining what * means if you are using it thanks
Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given: A1 = 0.94 in2, A2 = 0.38 in2, P1 = 81 kips, P2 = 49 kips, P3 = 31 kips and E = 29x106 psi Your final answer should have three decimal places
The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected to an axial load of 50 kNkN. Est=198 GPa�st=198 GPa, νst=0.32�st=0.32.
Two forces FA =168 lb and FB =265 lb are acting on the bracket shown with axes x,y,v and w indicated. If the angle measurements on the figure are c=20o , d=9o , f=15o and g=7o, determine the x-component of FA (lb).
A steel block is axially loaded with ? = 10 ?? as shown in the figure with length equal to 3? and crosssectional area equal to 1000 ??2 fits snugly between two rigid walls. Determine the change in length due to the applied load. Use ? = 0.30. (Answer in three decimal places and in mm)