P. 2. Consider a proposed new instruction named rpt. This instruction combines a loop's condition check and counter decrement into a single instruction. For example rpt x29, loop would do the following: if (x29 > 0) { x29 = x29 -1: goto loop a) If this instruction were to be added to the RISC-V instruction set. what is the most appropriate instruction format? b) What is the shortest sequence of RISC-V instructions that performs the same operation?

P. 2. Consider a proposed new instruction named rpt. This instruction combines a loop's condition check and counter decrement into a single instruction. For example rpt x29, loop would do the following: if (x29 > 0) { x29 = x29 -1: goto loop a) If this instruction were to be added to the RISC-V instruction set. what is the most appropriate instruction format? b) What is the shortest sequence of RISC-V instructions that performs the same operation?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given a 8-bit number at memory location 2050H. Write 8085 instruction to move the value stored at the following locations: Register B Accumulator 2052H Write a single program and show register and accumulator screenshot and also attach memory view. In sim8085 software.
6.) Select all the 8088 input signals that can cause the microprocessor to take an interrupt. a.) OSC b.) INTA c.) NMI d.) READY e.) INTR f.) IRQ 7.) Given the 8088 instruction "INT nn", how many possible types of interrupts are there for the 8088? a.) 2 b.) 4 c.) 8 d.) 256
1. Study this program, then answer the questions that follow: MOV AL, 64H ADD AL, 27H DAA a) What does the accumulator contain immediately after the ADD instruction is executed? What do the CY and AC flags contain? b) What does the accumulator contain after the DAA instruction is executed? What do the CY and AC flags contain?
Subject: MicroprocessorTopic: Output Devices When using the a basic 16x2 LCD in 4-bit mode, is it necessary to connect the R/W pin to the ground? Why?
2.Assuming the processor frequency is 20 MHz, find the highest square wave frequency that can be generated using Timer0 in 16-bit mode. (Calculations only, no code needed).
Continuing with a 32 Khz system clock/8000 Khz instruction clock, assuming a pre-scalar of1:1 (i.e. no prescalar), and 16-bit operation, if TMR0 is initialized to 64536, how many timeswill TMR0 need to be incremented before it overflows? How many instructions cycles will that take?
Describe the advantages and disadvantages of P, PI, PD and PID type control bodies by writing the transfer functions.
design and draw the full circuit diagram for the control circuit for the pc register
A program executes 200 billion instructions. It executes on an IBM processor that has an average CPI of 3 and a clock frequency of 3.0 GHz. How many seconds does the program take to execute? What is the cycle time of this IBM processor? Assume that an ARM processor takes 10 seconds to execute the program. What is the speedup provided by the IBM processor, relative to the ARM processor?
2 (a) Determine the control word ICW2 require for PIC controller so that IRQ0 to IRQ7 correspond to type numbers 30H to 37H , specify the memory location from which the processors will fetch interrupt vectors.
Industrial Motor Controls 18.a. The PLC motor speed control system you are working on has an analog current loop between the D/Amodule and the frequency inverter. What is the best method of checking this loop current?A. Open one of the signal wires in the loop and install a high-impedance VOM in series with the loop.B. Measure the voltage between the SIGNAL IN and +10V terminals of the inverter.C. Measure the voltage across the terminals of the D/A module.D. Open the loop and place a low-impedance VOM in series with the loop.18.b. The register that is assigned to a D/A module in a motor speed control circuit must be assigned to thatD/A module. How is this done?A. By placing the register for the D/A module in a configuration tableB. By forcing a value into the registerC. The registers are previously assigned by the PLC manufacturer.D. By setting DIP switches
Write a Verilog code with testbench for 16-bit up/down counter with synchronous reset and synchronous up/down.If up/down is set the counter is up counter and if it is not set, the counter is a down counter. submit the module code, testbench code, and the simulation results. PLEASE EXECUTE CODE IN VERILOG