P2: The 50-lb rectangular access door is held in the 90° open position by the single prop CD. Determine the force F in the prop and the magnitude of the force normal to the hinge axis AB in each of the small hinges A and B.

P2: The 50-lb rectangular access door is held in the 90° open position by the single prop CD. Determine the force F in the prop and the magnitude of the force normal to the hinge axis AB in each of the small hinges A and B.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter2: Basic Operations With Force Systems

Section: Chapter Questions

Problem 2.106RP: The trapdoor is held in the position shown by two cables. The tensions in the cables are T1=30lb and...

See similar textbooks

Related questions

Q: The assembly shown in the figure below consists of two sections of galvanized steel pipe connected…

Q: Problem 4: Consider the flow field formed by combining a uniform flow in the positive x direction…

A: Given Data:Flow field: Combination of a uniform flow in the positive x direction and a source…

Q: A horizontal shaft are held in long bearings and a disc is attached to the shaft at its mid-point.…

A: Given data:Horizontal shaftShaft diameter (d) = 20 mm = 0.02 mShaft span (L) = 1 mMass of disc (m) =…

Q: steel beam ABC is supported at A, B and C. The portion AB is 3m long and carries a central…

A: The beam is supported at A, B and CThe length of AB is .The load is applied at the center of AB.The…

Q: For P=8.5kN, determine the allowable stress if the thickness t is 20 mm. Section Properties At the…

Q: Consider a tall building. The air pressure at the bottom of the building is 101155Pa. The top of the…

Q: 6.172 Steam at 12.0 MPa, 480°C expands through a turbine operating at steady state to 10 bar,…

A: Given:P1= 12 MPa= 12000 kPa, T1= 480°C P2 = 10 bar=1000kPa, saturated vapor (i.e, x=1)The mass flow…

Q: from The water in a large tank exits through a horizontal circular pipe of diameter D=0.01m and…

A: Given:Assumption:Flow entrance to pipe is smooth and there are no minor losses.Flow in the pipe is…

Q: You do a series of tensile tests on plates of a magnesium alloy that have been subjected to prior…

A: Given:To find:

Q: A bowler sends his ball down the lane with a forward velocity of 10 ft/s and backspin of 12 rad/s.…

A: Draw the free-body diagram.

Q: Problem #3) A cord is wrapped around the inner hub of a wheel and pulled horizontally with a force…

Q: Q.2. Three forces act on the bracket. Determine the magnitude and direction 0 of F1 so that the…

A: Given:The forces are , .The magnitude of reaction force along is .Consider free body diagram as…

Q: Example 2. A cylindrical bar of 40 mm diameter and 1 m length is subjected to a tensile test. Its…

A: A cylindrical bar-Diameter d=40 mmLength L=1 mLongitudinal strain is 6 times lateral strainModulus…

Q: A uniform 200-lb boom that is 24 ft long is supported by a cable as shown in the accompanying…

Q: 285 A gate having the shape shown in Fig. P2.85 is located in the vertical side of an open tank…

Q: 7-118 Refrigerant-134a is throttled from 900 kPa and 35°C to 200 kPa. Heat is lost from the…

A: Given the question thatLet p1 be the pressure at the entry position = 900 kpaLet p2 be the pressure…

Q: A car weighs 2200 lb and is travelling 100 mi/h on a race track that is on a 3% upgrade. The car is…

A: The objective is to determine maximum car acceleration.

Q: The cylinder of W=253 N is supported by three cables as shown, Find 1-the angle of AB with…

A: Write the coordinates of each point.As per the guidelines, we solve only first three subpart, for…

Q: A B IB В ФО P

A: Given:1-The initial angular velocity of disk B is v0, let v0=w0 2-The mass of the disk A is mA.3-The…

Q: Air enters a turbine at a pressure of 2.2 MPa and a temperature of 816 K. The air exits at a…

Q: 4. The pressure in a stationary liquid depends on the position below the surface z according to p(2)…

Q: 3. Is there an ASTM standard concerning shaved or crushed ice?

A: There does not appear to be an ASTM standard specifically concerning the machines or processes for…

Q: The tension in cable AC is196 kN. What is the tension T?

Q: Determine the magnitude of the moment of the force F={50i− 24 j − 80k}N about the base line CA of…

A: objective is to determine the magnitude of moment of force F about base line CA

Q: Q1. Prove that the minimum thickness of a spherical shell which can withstand the internal pressure…

Q: -127. Determine the clamping force exerted on the mooth pipe at B if a force of 20 lb is applied to…

Q: Motorized moving platform is lifting a car with some acceleration. If the combined weight of the…

A: Mass of platform = 2800 kgMass of the lift = 200000 kgFind the maximum acceleration before tipping

Q: A rectangular channel of 3 m width is carrying a discharge of 6 m³/s considering that acceleration…

Q: The jet plane is flying upward such that its wings make an angle of attack of 15° with the…

Q: 1. An 10-lb collar C slides on a 20º inclined rod between springs A and B. If the collar is pushed…

Q: The 0.39*0.81-m lid ABCD of a storage bin is hinged along side AB and is held open by two cords ED…

A: Write the given data.

Q: The 1.06-in.-diameter rod in (Figure 1) is subjected to the loads shown. 9 in. 200 lb 300 lb 3 in.…

Q: Air flows at 700 m/s through a long duct in a wind tunnel, where the temperature is 15∘C and the…

A: Given data as per questionAir velocity=700m/sAbsolute pressure=85kpaTemperature in wind tunnel=15…

Q: An engineer designing a light aircraft is trying to make an estimate of the radius of the propeller…

Q: Q1/Determine magnitude of force at DG, DF,CF,AF and AB members by using joint method F 100 N 2m 100…

A: Find the magnitude of force at DG,DF,CF,AF and AB members by using joint method.

Q: Determine the horizontal and vertical components of reaction at pin A and the tension at cable AB.…

A: Given:- The equllibrium equation is:

Q: b) If one mole of air (rigid diatomic gas) is initially at 20 °C, is compressed and expanded 7- fold…

A: The initial temperature is The compression ratio is The number of moles of gas is .The heat…

Q: Ocean thermal energy conversion (OTEC) plants use the temperature difference in the ocean (80°F at…

A: It is asked to find the condensation coefficient based on the inside tube area

Q: A vapor-compression refrigeration cycle with refrigerant-134a as the working fluid operates between…

Q: Calculate the work done by the gas during process. Express your answer in terms ofand .

A: Given :To Find : The work done by the gas during process

Q: Coefficient of permeability of an underground stratum is 0.001 m/s. Discharge obtained from a well…

Q: The bench vice shown in Fig. is used to fix a cubic wood sample with a hole. The wood sample has a…

A: The length of wood is The diameter of hole is .The compressive strength of wood is The yield…

Q: A) A 0.4 m diameter fan running at 970 rev min¹ is tested when the air temperature is 10 °C and the…

A: Given data:Diameter of original fan (D1) = 0.4 mSpeed of original fan (N1) = 970 rpmAir temperature…

Q: Find the natural constraints for the turning crank shown below. CÂ cŷ

A: to find:the number of natural constraints.given:the figure

Q: The uniform lamina of density 2.2 kg/m2. for a=2.2 m,b=4.8 m,c=8 m,d=8.9 m, 1- x-co-ordinate of…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Assumption :steam considered as saturated vapor at each turbine exitGiven data ideal reheat Rankine…

Q: 21 2.2 2.3 24 2.5 A two-stage, single-acting air compressor with a polytropic index of 1.35 runs in…

A: Given:Polytropic index (n) = 1.35Inlet pressure (P1) = 80 kPaInlet temperature (T1) = 30°C = 303…

Q: How do gear ratios in a mechanical transmission system influence torque and speed output, and what…

A: Gears are fundamental components in mechanical systems that transmit rotary motion and force from…

Q: At a point in a strained material, if two mutually perpendicular tensile stresses of 200 kg/cm² and…

A: A stress element is given as shown-Tensile stresses-Also, To Find-The tangential stress on the 15o…

Q: can explain D,E,F more clearly also

A: d ) The force required for circular motion is the centripetal force, which is provided by the lift:…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

P2: The 50-lb rectangular access door is held in the 90° open position by the single prop CD.
Determine the force F in the prop and the magnitude of the force normal to the hinge axis
AB in each of the small hinges A and B.
12"
40"
C
2
B
48

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Force F in the prop and the magnitude of the force normal to be determined:

VIEW

Step 2: Explanation for Force F in the prop and the magnitude of the force normal:

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.
The center of gravity of the 3000-lb car is at G. The car is parked on an incline with the parking brake engaged, which locks the rear wheels. Find (a) the normal forces (perpendicular to the incline) acting under the front and rear pairs of wheels; and (b) the friction force (parallel to the incline) under the rear pair of wheels.
The homogeneous 80-kg sign is suspended from a ball-and-socket joint at O, and cables AD and BC. Determine the forces in the cables.
The walkway ABC of the footbridge is stiffened by adding the cable ADC and the short post of length L. If the tension in the cable is not to exceed 420 lb, what is the smallest value of L for which the 160-lb person can be supported at B?
The 180-lb homogeneous bar is supported by a ball-and-socket joint at A and two cables attached to B. Determine the forces in the cables.
The 80-lb homogeneous plate is supported by a ball-and-socket joint at A, a slider hearing at B, and the cable CE. A 120-lb vertical force is applied to the corner D. Determine the force in the cable and the magnitude of the bearing reaction at B.
Bar AB of negligible weight is supported by a ball-and-socket joint at B and two cables attached at A. Draw the FBD for the bar, recognizing that it is a two-force body. Determine the number of unknowns.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
Two concrete blocks weighing 320 lb each form part of the retaining wall of a swimming pool. Will the blocks be in equilibrium when the pool is filled and the water exerts the line loading shown?
Find the force P required to (a) push; and (b) pull the 80-lb homogeneous roller over the 3-in. curb.
The homogeneous 20-kg door is held in the horizontal plane by a thrust hinge at O, a hinge at A, and the vertical prop BC. Determine all forces acting on the door.
The trapdoor is held in the position shown by two cables. The tensions in the cables are T1=30lb and T2=90lb. Determine the magnitude of the single force that would have the same effect on the door as the cable tensions.