P/Aand(oalalowMJAr?(os)aller54000If it is pinned at its top and bottom, and a compressive load P is applied at point A, determine the maximum allowable magnitude of Pusing the equations oalow =with (a)allow = 21 ksi(KL/r)?Express your answer to three significant figures and include appropriate units. 5.25 in. 70.5 in.-x 10 in.´0.5 in.-* 0.5 in.10 in.

Solution Given that (σb)allow=21 ksi

Answered: P/A and (oalalow MJAr? (os)aller 54000…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Note: SN is equal to 18, topload will be equal to 118kN
A spiral column carries a dead load of 1070 kN and a live load of 980 kN. If fc' = 27.50 MPa Fy = 413.50 MPa. Use U = 1.2D + 1.6L, Ф = 0.65, ρ = 0.01 1. Which of the following gives the value of the diameter of spiral column. a. 440 mm b. 420 mm c. 450 mm d. 510 mm 2. Which bar size will provide least number of pieces allowed?. a. 16 mm b. 22 mm c. 20 mm d. 25 mm 3. Which of the following gives the possible spacing of the 10 mm0 spirals. a. 30 mm b. 40 mm c. 60 mm d. 60 mm
The loading on the bookshelf is distributed as shown. Determine the magnitude of the equivalent resultant location, measured from point O.
A column in the upper story of a building is subjected to a compressive load from the followingsources: dead load = 30.8 kips, occupancy live load = 1.7 kips, roof live load = 18.7 kips, and snowload = 19.7 kips.a. If load and resistance factor design (LRFD) is used, determine the factored load (requiredstrength) to be used in the design of the column. Which ASCE load combination controls?b. What is the required design strength of the column?c. What is the required nominal strength of the column for a resistance factor phi of0.9?d. If allowable strength design (ASD), determine the required load capacity (requiredstrength) to be used in the design of the column. Which ASCE load combination controls.e. What is the required nominal strength of the column for a safety factor Omega of 1.67.
Determine the slenderness ratio and the Euler buckling load for round wooden dowels that are 3.00 m long and have a diameter of (a) 19 mm and (b) 29 mm. Assume E = 14 GPa. Answer:(a) Slenderness ratio = Pcr = N (b) Slenderness ratio = Pcr = N
Determine: 2Z1 + 5Z2 show solutions with steps asap
NEED HELP ASAP PLEASE!!! A horizontal shelf AD of length L = 740 mm, width b = 360 mm, and thickness t = 30 mm is supported by brackets at B and C [see part (a) of the figure]. The brackets are adjustable and may be placed in any desired positions between the ends of the shelf. A uniform load of intensity q. which includes the weight of the shelf itself, acts on the shelf [see part (b) of the figure]. A L (a) D L (b) Determine the maximum permissible value of the load if the allowable bending stress in the shelf is Oallow = 7.5 MPa and the position of the supports is adjusted for maximum load-carrying capacity. Round to two decimal places. qmax kN/m
A 5-kip crate is supported by a pulley system and a horizontal force P.a) Find P and the angle α. Report your answer in kips (1 kip = 1000 lbs).b) For this problem if you double the weight of the crate, will the force P double? Briefly explain why or why not.
Determine the unstretched length of DB to hold the40-kg crate in the position shown. Take k = 180 N>m.
Determine the magnitude of the resultant of the external forces, K(kips) *kips(k)- a unit of force, equivalent to 1000lbs. (Av, Ah, Bv). Add figure if necessary.
1. A column in a building is subjected to the following service load effects: Dead Load = 40 KNWind Load = 36 KN Compression load Roof Live Load = 22 KN Rain Load = 32 KN Compression load a. If LRFD is used, determine the factored load to be used in the design of the column. b. What is the required design strength of the column?
A column in the upper story of a building is subjected to a compressive load from the followingsources: dead load = 30.8 kips, occupancy live load = 1.7 kips, roof live load = 18.7 kips, andsnow load = 19.7 kips. Determine the factored load (required strength) to be used in the designof the column. Which load combination controls? What is the required design strength of the column? What is the required nominal strength of the column for a resistance factor of 0.9?

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS