asap The parameters of the exact equivalent circuit for a three-phase, A-connected, 400-V, 10-hp, 50-Hz, six-pole induction motor aregiven in ohms per phase referred to the stator:R1 = 0.9, R2= 0.45, X = 1.5, X12= 0.6, and Xm = 45. The totalfriction, windage, and core losses can be assumed to be constant at600 W, independent of load. For a per-unit slip of 0.02, when themotor is operated at rated voltage and frequency, calculate thestator input current, the power factor at the stator terminals, therotor speed, output power, output torque, and efficiency.For the motor specified in problem 1, compute the following:a) The load component I2 of the stator current, the internaltorque T, and the internal power Pm for a slip of 0.02.b) The maximum internal torque, and the corresponding slipand speed.c) The internal starting torque and the corresponding stator loadcurrent I2.d) Predict and draw the Torque-Speed curve for this motor.e) The acceleration torque of this motor if the load torque is1.2.constant.d bu usino the Y/A

As per Bartleby guidelines we are allowed to solve only one question with maximum three subparts,…

parameters of the exact equivalent circuit for a three-phase, connected, 400-V, 10-hp, 50-Hz, six-pole induction motor a given in ohms per phase referred to the stator: R1 = 0.9, R2= 0.45, X1 = 1.5, X12= 0.6, and Xm = 45. The tot friction, windage, and core losses can be assumed to be constant 600 W, independent of load. For a per-unit slip of 0.02, when th motor is operated at rated voltage and frequency, calculate tI 1. The orminols t

parameters of the exact equivalent circuit for a three-phase, connected, 400-V, 10-hp, 50-Hz, six-pole induction motor a given in ohms per phase referred to the stator: R1 = 0.9, R2= 0.45, X1 = 1.5, X12= 0.6, and Xm = 45. The tot friction, windage, and core losses can be assumed to be constant 600 W, independent of load. For a per-unit slip of 0.02, when th motor is operated at rated voltage and frequency, calculate tI 1. The orminols t

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The armature of a 400V, 6-pole, 25 Hz single-phase series motor is lap-wounded with 504 conductors Motor field winding has effective resistance and leakage reactionance are 0.06 22 and 0.05 12, respectively and has 18 turns. However, the armature winding has a leakage reactance of 0.04 12 and negligible resistance. At rated motor current of 300A, the flux per pole is 0.05 Wb, the short circuit current is 50A and the equivalent current to iron losses is 40A. Find motor speed , torque and efficiency at rated current .
The primary leakage impedance and equivalent secondary impedance referred to stator atstandstill of a 3-phase, 220 V, 50-Hz, 4-pole induction motor are (0.4 + 3j)ohms and (1.2 + j1) ohms per phaserespectively. If the magnetizing current is neglected, determine the maximum torque the motor candevelop and slip at which it occurs.
A three phase, 4 pole, 3300 V, 50 Hz, star connected Induction motor, has identical primary and referred secondary impedance of value 3+j9 Ohm per phase. Using the approximate circuit, calculate: A. The full load torque at rated slip of 5%. B. The maximum torque at normal voltage and frequency.
A four-pole, single-phase, 120 V, 60 Hz induction motor gave the following standstill impedances when tested at rated frequency:Main winding : Zm =1.5+j4 ohmsAuxiliary winding : Za =3+j6 ohmsa) Determine the value of external resistance to be inserted in series with the auxiliary winding to obtain maximum starting torque as a resistor split-phase motor.b) Determine the value of the capacitor to be inserted in series with the auxiliary winding to obtain maximum starting torque as a capacitor-start motor.c) Determine the value of the capacitor to be inserted in series with the auxiliary winding to obtain maximum starting torque per ampere of the starting current as a capacitor-start motor.d) Compare the starting torques and starting currents in parts (a), (b), and (c) expressed as per unit of the starting torque without any external element in the auxiliary circuit, when operated at 120V, 60Hz.
A 110-V, 50-Hz single phase induction motor (split -phase) has the following constants for the main and auxiliary windings: Main winding, Zm (1.2 +j 25) ohm and auxiliary winding, Z,= (12+j 5) ohm. Determine (i) total current and power factor currents at time of starting, and (ii) phase angle between the main winding current and starting winding current.
Q2. For a 10 kW, 380V, three-phase, four-pole, 1200 r/min, delta-connected induction motor. Adopt a specific magnetic loading of 0.4712 Wb/m2 and a specific electric loading of 23000 ampere-conductors per metre. The motor has a full-load efficiency of 85% and a full-load power factor of 0.8. A square pole design may be assumed and the stator leakage impedance voltage drop may be ignored. Assume also that the winding is full-pitched and uniformly wound. To calculate the following design parameters (a) The approximate outer diameter and length of the rotor core (b) the air gap length of the motor (c) the turns per phase (d) the number of conductors per slot, if 3 slots per pole per phase are chosen
Three-phase induction motor, 460 V 50 Hz, 4 poles, 50 hp with Delta, operating at 3.8% slip rated torque when receives Line Voltage 460 V, 50 Hz The parameters of the equivalent circuit per phase are as follows.R1 = 0.33, X1 = X2 = 0.42 and Xm = 30 Ohm / phase.Answer the following questions by neglecting the mechanical losses, Core losses and Stray load losses.A) Value of the rotor resistance R2 B) Maximum torque and rated speed C) line current and starting torque of motor
A 3-phase induction motor, 440-V, 50-Hz, 6-pole, delta-connected has the following equivalent-circuit parameters at normal frequency:R1.2 ohm, R'2=0.18 ohm, X1= x'2=0.58 ohm, all per phase values. The machine is subjected in service to an occasional fall of 40% in both voltage and frequency. What total mechanical load torque is it safe to drive so that the machine just does not stall under these conditions? When operating at normal voltage and frequency, calculate the speed when delivering this torque and the power developed. Calculate also the speed at which maximum torque occurs. If V and f were both halved, what would be the increase in starting torque from the normal direct-on-line start at rated voltage and frequency? If now the machine is run up to speed from a variable-voltage, variable-frequency supply, calculate the required terminal voltage and frequency to give the 'safe' torque calculated above: (i) at starting, (ii) at 500 rev/min. Repeat (d) for the machine to develop a…
A 220 V, single-phase induction motor gave the following test results:Blocked-rotor test: 120 V, 9.6 A, 460 WNo-load test: 220 V, 4.6 A, 125 WThe stator winding resistance is 1.5 Ω, and during the blocked-rotor test, the starting winding is open. Determine the equivalent circuit parameters. Also, find the core, friction and windage losses.
1.Show that if three phase currents, each of equal magnitude and differing in phase by 120degree, flow in a three phase winding that are 120 degree apart from each other then it willproduce a rotating magnetic field of a fixed magnitude. 2. A three phase, 5-hp, 60Hz, 115V, 4-pole induction motor is operating at rated voltage, rated frequency, and 125 percent rated load has an efficiency of 85.4 percent. The stator conductor loss, rotor copper loss and core loss are 223.2W, 153W, and 114.8W respectively.Sketch the power flow diagram, enter the given data, and determine i) shaft speed ii) shaft torque 3. Can single phase induction motor be self-started? Explain the operation of a split phase single phase induction motor?
5.a. A motor which is designed with nonstandard operating characteristics is classified as aA. definite-purpose motor.B. special-purpose motor.C. general-purpose motor. 5.B. For a repulsion motor with bmshes set in the neutral position, what type of winding is needed to producestarting torque?A. A capacitor-phase windingB. A squirrel-cage windingC. A starting winding
(b) A 415V, 50Hz, delta-connected, 4-pole, squirrel cage induction motor has a perphase equivalent circuit as shown in Figure Q4(b). The circuit parameter values (in Ω/phase) for the stator is as follows: R1 = 0.095 Ω ; R2 = 0.06 Ω; X1 = 0.68 Ω ; X2 = 0.67 Ω; Xm = 18 Ω The motor is running at 1400 rpm at full-load. The core loss of the motor is assumed to be zero. The total friction and windage losses is 600 W, independent of load. Determine the efficiency of the motor.