PART 1. AREA & VOLUME OF PRISMS Draw the indicated views for the isometric drawing below. Isometric Drawing: 1. Top View: 2. Left View: Front 3. Front View: CON #usid ed

Q: 1) Use the method of joints to find the force in each member of the truss shown below in Fig 5.1…

A:

Q: 2.45 La barra rígida ABC está suspendida de tres alambres del mismo material. El área de la sección…

A: Given question is  " The rigid bar ABC is suspended from three wires of the same material. The…

Q: i). A town produces 8 million litre of sewage per day. BOD of sewage is 260 mg/L, it is to be…

A:

Q: For the loading on the beam calculate the maximum normal stress due to bending on a transverse…

A: Beam size = 100mm × 200mm  Determine the maximum normal stress due to bending at section C.

Q: A driver is traveling 70 mi/hr on a road with a -2% downgrade. The driver's vehicle has a braking…

A: speed V = 70 mi/hr Grade G = -2% braking efficiency = 90% Stopping sight distance = 500 ft lateral…

Q: 5. The 1800-N force F is applied to the end of the I-beam. Express Fas a vector using the unit…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: Station 1+100 Station 1+120 Station 1+140 Station 1+160 Station 1+180 Subgrade Cross Sections for…

A:

Q: A flood control structure having an expected life of n years is designed by considering a flood of…

A: Expected life=n yearsFlood return period=T yearsT=n and n→∞

Q: Find the tension in the active tension counters

A: Find: The Tension in the active tension counters

Q: A solid circular shaft of 6m length is built in at its ends and subjected to an externally applied…

A:

Q: A tension member is composed of two 4x10 plates. They are connected to a gusset plate with the…

A: A tension member is composed of two 34×10 plates. A36 grade of steel used Diameter of bolts, d = 1…

Q: structures method of sections algebra,geometry and trigo

A: Consider Moment equilibrium at point D Fy*18 = 13*6+9*x tan50 = x6 x = 6*tan50 x = 7.15' Now Fy*18 =…

Q: The absolute maximum Bending Moment in a simply supported beam of span 20 m due to a moving udl of 4…

A:

Q: The average daily traffic on a stretch of road is 300 commercial vehicles per lane per day. Design…

A:

Q: 1) Use the method of PINS to determine the true magnitude and direction of the forces in all the…

A: Weight, W = 500 lbs  It is asked to determine the forces in the members using method of pins.

Q: A cantilevered prismatic beam (ABC) has a concentrated moment applied at the mid span (B). The beam…

A: Deflection at C is given by δc = Deflection caused at C by M and Deflection resisted at C by cable…

Q: 1000 mm Section 1 f'c 8-36 Ø fv 32 415 800 mm

A: For the given section we have to find the 1 Depth of neutral axis (C)  2 Depth of compression…

Q: If the dynamic viscosity of a fluid is 0.5 poise and specific gravity is 0.5, then the kinematic…

A:

Q: 1. Refer the Fig. 1. Estimate the side resistance Qs by a. Meyerhof's method. K= 1.5 and 8' 0.6 Ø1…

A: Size of the concrete pile:- D= 460mm k= 1.5 L= 20m To find: (a) side resistance Qs by Meyerhof's…

Q: due to cost and right of way constarints rv is determined to be 890 ft. superlevation is 12% what…

A: Given; Radius(R) = 890 ft. superlevation(e) = 12% = 0.12

Q: A steel frame is shown in the given figure. A L B L O L/2 ALERI C El Constant D If joint O of the…

A:

Q: 2 Rod reading on A Rod reading on B 1.71 6.25 Instrument at A Instrument at B 0.52 4.49 Rod

A:

Q: PLEASE ANSWER QUESTION 4 stated above    HOW DID WE OBTAIN 0.38 and 0.07 for solution 3.…

A: The design speed = 65 mph The number of lanes = 8 The superelevation rate = 6% The initial grade =…

Q: 1.47 A cylinder contains 12.5 ft³ of air at 120 °F and 40 psia. The air is then compressed to 2.50…

A:

Q: A 4-hour rainfall in a catchment of 250 km² produces rainfall depths of 6.2 cm and 5.0 cm in…

A: 4-hr rainfall,Catchment area A=250 km2,Rainfall depths = 6.2 cm & 5 cm in successive 2-hour unit…

Q: 1- Define underground storage tank systems and give some establishments that use USTs

A: Underground storage tank systems (USTs) are carefully designed and constructed…

Q: The infiltration rate for excess rain on a small area was observed to be  11.5 cm.hr-1 at the…

A:

Q: A grass-lined trapezoidal channel has a bottom width of 40.0 ft with 4H:1V side slopes. The channel…

A: bottom width b = 40 ft side slope 4H:1V manning's n = 0.038 side slope 20:1 Longitudinal slope S =…

Q: Prob-5 Hospital workers who are routinely involved administrative radioactive tracer to patients are…

A: Given; Sample size n = 28 sample mean x bar = 5.145 sample std dev s = 0.7524

Q: For the truss shown below, P = 9.2 kips, a = 8 ft, and b = 6 ft. Determine the force in member 2…

A: The truss with loading is shown below.

Q: A discharge of 0.6 m³/s flows through a horizontal bend as shown in figure. Calculate the force on…

A: Given; Discharge (Q) = 0.6 m3/s Dia. at section 1 = 15 cm = 0.15 m Dia. at section 2 = 5 cm = 0.05 m…

Q: After placement, the temperature of the concrete was measured and recorded by thermal sensors during…

A: Datum Temperature of concrete mix = -50 C Find: Maturity of the concrete at the end of 7 days using…

Q: moment A P514 B B

A: Given one side hang beam with BMD diagram and asked to draw the deflection curve, shear diagram and…

Q: The question in the subject of advanced soil mechanics, dear, answer all points, thank you A sand…

A: A sand sample- Axial stress = 200 kPa, Radial stress = 50 kPa, The specific volume before shear…

Q: Find Lateral Deflection at joint E in mm.

A: A truss supported at hinged support at A and roller support at E, is loaded with vertical loading…

Q: Calculate the maximum tensile and compressive stresses in the section of BC of the beam. 15 ເຄດາ -…

A:

Q: For masonry built in 1:1:6 cement- lime. sand mix mortar or equivalent, the horizontal shear stress…

A:

Q: Problem 1. A 2300-ft equal-tangent crest vertical curve is currently designed for 60 mph. This curve…

A: L= 2300 feet V= 60 mph initial grade G1 = +3.5%  To find: 1. The min k-value under 60 mph design…

Q: Two silicon wafer sizes are to be compared: a 6.0-in wafer with a processable area = 5.85-in…

A: case 1- Wafer size 1 = 6.0 in processable area 1 = 5.85 in case 2- Wafer size 2 = 12.0- in…

Q: 4. Determine the member end moments and reactions for the three- span continuous beam shown due to…

A: Three span Continuous beam with uniformly loaded of intensity 32 kN/m Support settlement at B = 15…

Q: -X 3 kips 4 3 Y Y -X

A: given- slope= 4/3 f= 3kips Concept- by finding x component and y component- Fx= F cosθFy= F sinθ…

Q: 2) Use the method of joints to find the force in each member of the truss shown below in Fig 5.2

A: The truss is shown below

Q: Return Period 1. Maximum depth of precipitation of certain area is presented below. Based on the…

A: Depth of precipitation of certain area from year 1995 to 2015

Q: A 4 inch thick rubber pad sandwiched a plate as shown in the figure. Find the displacement (in…

A: Thickness of rubber pad , c = 4in , Load Applied , P =2592lb , E = 500psi , v = 0.53 , a = 9.7in , b…

Q: , A rectangular wooden object (s.g. = 0.72), 20cm x 20cm in cross sectional area and 4 m in length…

A: Weight of lead(WL) Weight of lead = unit weight of lead * Volume of lead Weight of lead = 110 *…

Q: Express F as a vector in terms of the unit vectors i, j, and k. Determine the magnitude of…

A: The below figure is given;

Q: A W = 12 kips/ft B hinge 6 kips/ft C 6 kips D

A: A beam is fixed at A and roller supported at C also, an internal hinge is present at B. To determine…

Q: Draw the shear and bending moment diagrams for the beam and loading shown. 20 kN 10 kN A V B 2 m 2 m…

A: Overhang beam with UDL and point loads respectively,

Q: Problem 6.93 The cross section is rectangular with a base of 5 in and height of 8 in. A force of P =…

A: A beam at A supported by a vertical hinge and at B, the reaction developed is uniformly distributed…

Q: A bar of circular cross-section varies uniformly from a cross-section 2D to D. If extension of the…

A: