Compute the total volume using average end area method. Then show the solution using basket method. Round off answers in two decimal places and provide illustrations for the problem Subgrade Cross Sections for Proposed RoadwayLeftCenterRightStation 1+1006.5-6-6-6.518Station 1+120+4.5-7.5+2-7.51715Station 1+140-8.5-8.5-8.5-9-3.5186.16Station 1+160+6-8.5-8.51915Station 1+180-7.5-7.5+61717

Answered: Image /qna-images/answer/ca2937bd-7b67-4657-8b90-e9a4d9bc2197.jpg

Station 1+100 Station 1+120 Station 1+140 Station 1+160 Station 1+180 Subgrade Cross Sections for Proposed Roadway Left Center -6.5 응 응응응 6 6 윽 공공공 쇽 -8.5 용을 6 응응응쁙 곢 공공 공즉 18 +4.5 17 음을 +6 19 -8.5 7 -7.5 -8.5 -8.5 Right -6.5 7 17 15 -3.5 16 -2 15 +6 17

Station 1+100 Station 1+120 Station 1+140 Station 1+160 Station 1+180 Subgrade Cross Sections for Proposed Roadway Left Center -6.5 응 응응응 6 6 윽 공공공 쇽 -8.5 용을 6 응응응쁙 곢 공공 공즉 18 +4.5 17 음을 +6 19 -8.5 7 -7.5 -8.5 -8.5 Right -6.5 7 17 15 -3.5 16 -2 15 +6 17

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q2) For the table below. Find the equivalent axle load. For the standard axle load is 80 Axle load…

A: To calculate the equivalent axle load, we can use the concept of Equivalent Single Axle Load (ESAL).…

Q: Determine the spacing between stirrups at maximum shear force for the simply supported beam that has…

A: Since the beam is symmetrically loaded we get equal reaction at supports RL = RR = Wu*L2 Wu =…

Q: Problem 3 Complete 5.130 from the course text. 5/130 Determine the shear force V and bending moment…

Q: A lever is supported on two hinges at A and C. It carries a force of 3 kN as shown in the figure…

A: Bending moment at B ?

Q: A 4-hour storm occurs over an 80 km² watershed. The details of the catchment are as follows. Sub…

A: area km2 loss @ mm/hour 1sthour rainfall in mm hour 2ndhour rainfall in mm hour 3rd hour rainfall in…

Q: If the internal radius of a hollow shaft is n times the external radius, then ratio of torques…

Q: Two plates 16 × 10 are welded to a W10 X 49 to form a built-up shape, as shown in Figure P4.9-7.…

A: Sectional properties: W10×49 Area = 14.4 in2Ixx=272 in4Iyy=93.4 in4bf = 10 in fy=50 ksiKL=25 ft

Q: Draw a neat, fully annotated shear force and bending moment diagram, including the maximum in span…

A: The loading diagram is shown below. Hint : Horizontal distance of BD=3 cos45°=2.12 mVertical…

Q: Calculate the loadings on the column. The column will be supporting the loads from the roof and…

A: Roof Slope = 15° , Eave's Height = 5m , Bay Width = 6.4m , Dead Load, Pd=200kips , Floor Live…

Q: An alert driver used brakes to avoid an accident when suddenly a person steps from behind parked car…

Q: (Use section method) and Draw the shear and bending moment diagrams for the beam and loading shown.

Q: Problem # 6.0 For the tension member shown, compute the tensile design strength. Weld -6" PL 4X6 A36…

A: The tension member is given as To find:- Tensile design strength

Q: Calculate the normal component of acceleration when 8 m³/s of water passes over the bucket of a…

A: Q = 8 m3/s A = 1×0.5 m2 Radius, R = 4 m The normal component of acceleration is =?

Q: 4) Use the method of MEMBERS to determine the true magnitude and direction of the forces in members…

Q: Use the method of SECTIONS to find the true magnitude and direction in bar FE of the truss shown…

A: Given a loaded truss with members AB,BC,CD,CE,BE,BF,EF. Two external loads 500lb and 1000lb are…

Q: The base length of the runway at the mean sea level (MSL) is 1500 m. If the runway is located at an…

Q: How do I get the support forces

A: The x and y are the vertical and horizontal distances: x=12cos60=6 fty=6sin60=5.196 ft

Q: Draw the free body diagrams of each section.

Q: Calculate the density of water vapor at 350 kPa abs and 20 °C if its gas constant (R) is 0.462 kPa.…

A: The water vapor at pressure, P = 350 kPa Temperature, T=20 °C=293 K. Gas constant, R=0.462…

Q: If Q produced by a pump is less than the required Q, what should be the step taken by you as a…

A: If the Q required is greater than actual Q production, then best available option is Increasing the…

Q: determine the end moments of the beam shown in Figure 11.9a. Assume support B settles 1.5 in, and…

Q: A ball moving on a smooth horizontal table hits a rough vertical wall, the coefficient of…

Q: exceeded? b. How accurately should each 30.000 m distance have be measured so that the estimated…

A: Theodolites are essentially the most precise tools for measuring the horizontal and vertical angles…

Q: A timber beam is 100 mm wide and 150 mm deep. The beam is simply supported and carries a central…

A: Given- A timber beam- width=100 mm, depth=150 mm, Simply supported beam- central concentrated load=W…

Q: Calculate the plastic modulus Sx of the section shown below. All dimensions are in mm. Note: The…

A: Determine the plastic modulus Sx of the section.

Q: 6-7. Draw the influence line for (a) the moment at B, (b) the shear at C, and (c) the vertical…

A: A beam with vertical roller support at A such that it resists only moment and horizontal force and a…

Q: III. A cantilever beam having a width of 350mm, height of 650mm and length of 5m is reinforced with…

A: Width of beam = 350 mm Depth of beam = 650 mm Span of beam = 5 m

Q: Problem 4. The Warren truss loaded as shown in the figure supported by a roller at C and a hinge at…

Q: Q2- In a traverse ABCD the angles to the right are measured and the azimuth of the lines PA and DR…

Q: A prismatic bar of length 'L' loaded under its own weight (W=pg) is fixed to the roof of a building…

A: given : length = L weight ( W ) density = ρ acceleration due to gravity = g γ= ρ.g To find :…

Q: A two spans continuous concrete beam is to be supported by three concrete columns spaced (7.0 m) on…

A: 2 span continuous concrete beam each of span 7m LL = 25 kN/m b = 300 mm h = 500 mm f'c = 28 MPa fy =…

Q: Requirements: Shear and Moment with diagrams Using slope deflection method

A: Given : Required : Shear and moment diagram

Q: In a closed traverse with five sides, the error found from fore bearing and back bearing of the last…

A: Closed traverse of 5 sides, Error e=+2o Correction to the third line = ?

Q: Using ultimate strength method to design a rectangular beam uf6. for a 10 m simple span to support a…

A: Span, L = 10 m Dead Load, DL = 20 kN/m Live load, LL = 30 kN/m fc = 28 MPa fy = 420 MPa b = 500 mm h…

Q: Draw the internal force diagrams of the given structure. Use E= 200GPa, I = 95e8mm*, A=1000mm². 20…

A: Find: (a) Axial Force in ab (b) Maximum moment in the structure

Q: Using the slope-deflection method, determine the end moments of the beam shown in Figure 11.9a.…

Q: A solid circular shaft of 6m length is built in at its ends and subjected to an externally applied…

Q: 1- Define underground storage tank systems and give some establishments that use USTs

A: Underground storage tank systems (USTs) are carefully designed and constructed…

Q: 2) Use the method of MEMBERS to determine the true magnitude and direction of the forces in members…

A: Find: Member forces by method of members

Q: When conducting CBR test, it is observed that the load dial reading at 2.5 mm penetration is 33…

Q: 12-56 Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of…

Q: Calculate the maximum tensile and compressive stresses in the section of BC of the beam. 15 ເຄດາ -…

Q: The sum of the moments about point A due to the forces and couples acting on the bar is zero. a)…

A: Sum of forces and couple about A = 0 Couple at A = 20 kNm Vertical force at A = 5 kN Horizontal…

Q: 4. Length of offset from long chord is equal to a)R-V R²-X² b) √ R--X²-(R-M) c)) √ R²-X² -(R+M) d) v…

Q: 3-11 4) Use the method of MEMBERS to determine the true magnitude and direction of the forces in…

Q: A circular barrel, 19 KN in weight, was used to separate water from glycerin as shown below. Both…

A: Barrel weight = 19kN , Specific Gravity of Glycerin = 1.56 Therefore, γgly= 1.56 × γw where…

Q: 1.1 AN SPECIFIC ACTING VERTICALLY OPEN WEIGHT ON IN THE CUBICAL 8 kN/m³ SIDE UPWARD TANK OF UP A AND…

A: Width of Open Cubical Tank, w=1.8m ,Height of Open Cubical Tank, h=1.8m Specific weight of oil, ρg…

Q: , A rectangular wooden object (s.g. = 0.72), 20cm x 20cm in cross sectional area and 4 m in length…

A: Weight of lead(WL) Weight of lead = unit weight of lead * Volume of lead Weight of lead = 110 *…

Q: The taped distance of a line is 86.67 meters using a 100 m. steel tape at a pull of 20 kg and…

A: Taped Distance of a line, Measured Length L = 86.67m , Designated length of steel tape ,l=100m…

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

Compute the total volume using average end area method. Then show the solution using basket method. Round off answers in two decimal places and provide illustrations for the problem

Subgrade Cross Sections for Proposed Roadway
Left
Center
Right
Station 1+100
6.5
-6
-6
-6.5
18
Station 1+120
+4.5
-7.5
+2
-7.5
17
15
Station 1+140
-8.5
-8.5
-8.5
-9
-3.5
18
6.
16
Station 1+160
+6
-8.5
-8.5
19
15
Station 1+180
-7.5
-7.5
+6
17
17

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Area calculations

VIEW

Step 3: Volume calculation

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular channel is to carries 1 m3/s. Determine the most cost effective cross-sectional dimension of the channel – width and depth. The slope of the channel is 0.01. Neglect free board. Mannings n = 0.011.
Question 4a pls
A road is tangent to a circular lake. Along the road and 12 miles from the point of tangency, another road opens towards the lake. From the intersection of the two roads to the periphery of the lake, the length of the new road is 11 miles. If the new road will be prolonged across the lake, find the length of the bridge to be constructed.
mnew 9
The angle between twointersecting fences is to be determined with a tape. Apoint on each fence line is established 30.0 m from thepoint of the intersection. If the distance between theestablished points is 12.20 m, what is the intersectionangle?
If full station is 100 m, the foot of the bridge located 145 m beyond station 14+00 should be A. 01+45 B. 15+45 C. 145+35 D. None of the above
plz, solve this question ,it is not graded question. Reg.no : 5395
Find the station kilometer of point B with curb radii of R1 and R2 according to the information given.
Find the station kilometers of point B with curb radii R1 and R2 according to the given.
Determine the stationing of point B of a 6degree curve. The length of line 1A is 807.6ft and line AB is 645.3ft. The beginning station of the project is at Point 1 and is assigned as 10+00. Use Arc basis.
Draw the cross section of a 4 lane divided national highway with with unpaved shoulder on a plain terrain with high rainfall. Mark the number of lanes, width of carriageway, camber, median, shoulder, drain, limits of ROW, building line and control line. Use IRC 73 as a guideline. Draw with appropirate scale.
From station 0 + 040 with center height of 1.2m. fill, the ground line makes a uniform slope of 6.5% to station 0 + 100,whose center height is 3.5 m. Findthe grade of the finished roadway. Select the correct answer: A. - 1.33%B. -2.00%C. + 2.00%D. - 1.85%