Part A A steel tube having an outer diameter transmit 9 hp when turning at 27 rev/min. 1 hp = 550 ft-lb/s. (Figure 1) Figure 2.5 in. is used 10 1 of 1 Determine the inner diameter d of the tube if the allowable shear stress is Tallow = 10 ksi.

Part A A steel tube having an outer diameter transmit 9 hp when turning at 27 rev/min. 1 hp = 550 ft-lb/s. (Figure 1) Figure 2.5 in. is used 10 1 of 1 Determine the inner diameter d of the tube if the allowable shear stress is Tallow = 10 ksi.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: Consider a rigid rod that is subjected to two external forces and is fixed to the wall at A. The…

Q: vehicles are approaching a road junction, both moving with speed (12.5 m/s). One vehicle has mass…

A: Mass of Car A (mA) = 1000 kgMass of Car B (mB) = 70 kgInitial velocity of both cars (v) = 12.5…

Q: Question 2: Determine the moment of inertia of the shaded area. 30mm 23mm 10mm x

A: Partition the area into simple disjoint shapes (areas) with known (or can be easily found)…

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 26 mm. Assume…

Q: The fluid in a manometer tube is 60 % water and 40 % alcohol (S.G.0.83). What is the manometer fluid…

A: Given Data

Q: 100 mm 6 in. 200 mm 140 mm 140 mm 2. Locate the centroid (x, y) for the angle's cross sectional…

A: A2 = A2 = A2 = 15707.96 A1 = A1 = 40292.04-> Centroiet of Rectangular point. X1 = 100…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A: Pressure angle is 20 degreeNumber of teeth on pinion is 24Number of teeth on gear is 96Pinion…

Q: At time t=0, the position vector of a particle moving in the x-y plane is r = 5.28i m. By time t =…

A: Given data as below:

Q: Two solid cylindrical rods support a load of P = 25 kN as shown. Rod (1) has a diameter of 16 mm,…

Q: Question #1: Determine the shear, axial, and bending moment distributions for the loaded beam shown…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat…

A: Given Tierod (1) Diameter=11mm Normal stress=75MPA Pipe(2)…

Q: A steel bar with a rectangular cross section of 4 inches by 3 inches is loaded by a force direction…

A: Given Data

Q: For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to…

Q: What are the precautions to follow when using the tirfor machine?

A: The Tirfor machine, also referred to as a hand winch or a pulling hoist, is an adaptable device used…

Q: What is capillary in fluids? Explain capillary rise as well as capillary fall. Also, provide the…

A: Capillarity is the property of fluid. Capillarity is the movement of liquid due to forces of…

Q: A force of P = 20 N is applied to the cable, which causes a 175 kg of radius of Gyration KG = 0.42m…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

Q: A centrifugal pump uses a 134767 rpm motor to pump 116334 kg/min of standard temperature water and…

Q: The system is at rest with the spring unstretched when theta = 0. the 5.3 kg uniform slender bar is…

A: mass,m=5.3 kgb=0.45 mto determine:(a) Spring constant k(b)magnitude of angular velocity

Q: 2. Plot the root locus for the system shown below. Determine the range of gain K for stability. C(s)…

A: Given;The characteristic equation is.By R-H Criteria. + 1100 + 72k0 + 0 +…

Q: An oil engine working on a dual combustion cycle, has a compression ratio of 16: 1 and the cut-off…

A: The compression ratio, r = 16:1The cutoff, V4 - V₃= 0.06(V1-V2)The maximum pressure, P4 = 70 barThe…

Q: the behaviour of sponge material under stress

A: When a sponge material is subjected to stress,it's behaviour can depend on different factors such as…

Q: What are the key factors that influence the compressible flow behavior in a gas turbine engine, and…

A: This question is based on the concept of Engine performance.

Q: The force P is applied to the 40-kg block when it is at rest. Determine the magnitude and direction…

Q: Compute the thread pitch and friction angle for a screw,

A: to compute the thread pitch and friction angle for a screw,

Q: The cover of a cylindrical pressure vessel made of cast iron is shown in fig.1 The inner diameter of…

A: Given:The inner diameter of the cylinder is .The internal pressure is limited to .The number of…

Q: A hollow mast of circular section as shown is to be stiffened by bonding two strips of the same…

Q: (a) Extend the control volume analysis used to derive the continuity equation to three-dimensional…

A: In these given problem , the questions a) ,b) & c) are different . According to our guidelines…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: Please write down Darcy’s law with pressure and potential form separately, explain the meaning of…

A: This law describe the fluid through the porous medium.French engineer Henri darcy governs the law…

Q: Determine the normal force, shear force and moment at point E and F. Tabulate the final anwer in…

Q: Determine the range of weights W for which the 81-lb block is in equilibrium. All wheels and pulleys…

Q: A test of 6 units of a product was continued until all units failed. The failure times were 5, 12,…

A: Total number of failures = 6The failure times were, 5,12,22,34,35,45 hours

Q: How do the different controllers help in operation?

A: In control systems, controllers are tools or algorithms that manage and control how a system or…

Q: Question 2) The figure shows a mechanical model of the Russel fracture traction device and the leg.…

Q: Determine the mathematical model for the translational-rotational dynamic system shown in the…

Q: Calculate the horizontal and vertical components of the hydrostatic thrust on the 90 cm radius…

A: Radius of cylindrical cover = 90 cm = 0.9 mγwater = 9.810 kN/m³θ = 90°h = 1.20 md = 3m

Q: Two rods are connected to the roof. All joints are hinged. AC = BC = 1 m. Load 'F KN' is acting in…

Q: Calculate the centroid of the composite shape AB= 85 C=1 BC = 12

A: The centroid of the composite shape.Given:The shape is shown below.

Q: A particle which moves with curvilinear motion has coordinates in millimeters which vary with the…

Q: Match the following terminology to the proper description. direction cosines alpha beta gamma…

A: 1.Direction cosines:The cosines of the angles between vector and the three positive coordinate axes,…

Q: water is flowing at 4 m/s in a penstock pipe of 4500 m long. if celerity of the pressure wave…

Q: Find the spectral radius of the matrix T; of Jacobi method for the following lineer system:…

Q: An ideal Rankine cycle, the boiler heat input is 59 kW and the condenser heat rejection is 39 kW,…

A: Given- Boiler heat input =59 KW condensor heat rejection=39KWDetermine- Thermal…

Q: How can the Bode plot be used to analyze and design control systems in mechanical engineering…

A: In control systems engineering, a Bode Plot is a graphical representation of a linear,…

Q: A piston ring of outer diameter 1.5354in and inner diameter of 1.496in is placed in a ring gage of…

A: given data:Piston ring outer diameter =1.5354 inchesPiston ring inner diameter=1.496 inchesInitial…

Q: For alloys of two hypothetical metals A and B, there exist an a, A-rich phase and a ß, B-rich phase.…

A: Given:Alloy composition and alpha and beta fractionTo find:Alpha phase wt % ABeta phase wt % A

Q: If 3.9 kg metal with 92 °C temperatures is immersed into 6 kg of water at 10 °C, what will be the…

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 20 mm. Assume…

A: Length of the link BCAngle made by link AB from the horizontal:Diameter of each pinSo the area of…

Q: The guide with the vertical slot is given a horizontal oscillatory motion according to x = 5.1 sin…

A: X = 5.1 inX = 5.1 Sin (3.4t)y = x²/8

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Need correctly. Thank you!!!

Part A
A steel tube having an outer diameter of 2.5 in. is used to
transmit 9 hp when turning at 27 rev/min.
1 hp = 550 ft-lb/s. (Figure 1)
Figure
2.5 in.
< 1 of 1
>
Determine the inner diameter d of the tube if the allowable shear stress is Tallow = 10 ksi.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Using Torsion equation

VIEW

Step 3: Inner diameter calculation

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
A thin-walled steel tube of rectangular cross section (see figure) has centerline dimensions b = 150 mm and h = 100 mm. The wall thickness t is constant and equal to 6.0 mm. Determine the shear stress in the tube due to a torque T = 1650 N · m. Determine the angle of twist (in degrees) if the length L of the tube is 1.2 m and the shear modulus G is 75 GPa.
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A standpipe in a water-supply system (see figure) is 12 ft in diameter and 6 in. thick. Two horizontal pipes carry water out of the standpipe; each is 2 ft in diameter and 1 in. thick. When the system is shut down and water fills the pipes but is not moving, the hoop stress at the bottom of the standpipe is 130 psi, (a) What is the height h of the water in the standpipe? (b) If the bottoms of the pipes are at the same elevation as the bottom of the stand pipe. what is the hoop stress in the pipes?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A stepped shaft (see figure) has diameter D2= 1.5 in, and a full quarter-circular fillet. The allowable shear stress is 15,000 psi and the load T = 4800 1b-in. What is the smallest permissible diameter D1?
A thin-walled steel tube having an elliptical cross section with constant thickness t (see figure) is subjected to a torque T = 18 kip-in. Determine the shear stress and the rate of twist in degrees per inch) if G = 12 × 106 psi, t = 0.2 in., a = 3 in., and b = 2 in. Note: See Appendix E, Case 16, for the properties of an ellipse.