Part A] Assuming a transmission line with Zo=50 ohms, draw the corresponding Bergeron diagram. (the answer is already on the graph, but please understand how it's drawn!) Part B] Plot the voltage waveforms at the input (in other words, v(0,t) and at the load (in other words, v(I,t). 1=0 Driver Z,, » T Load

Part A] Assuming a transmission line with Zo=50 ohms, draw the corresponding Bergeron diagram. (the answer is already on the graph, but please understand how it's drawn!) Part B] Plot the voltage waveforms at the input (in other words, v(0,t) and at the load (in other words, v(I,t). 1=0 Driver Z,, » T Load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.52P

See similar textbooks

Similar questions

Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
The units of admittance, conductance, and susceptance are siemens. (a) True (b) False
1/In the Transmission Line Simulator, the Transmission Line is connected in Nominal-Pi Circuit. Select one: True False
electrical engg .fig.shows a single-line diagram of a power system where the generator is connected to the bus 1 and the load is connected to the bus 2. The line impedance is 0.12 +j 0.23 pu on a 100 MVA a base. Per unit real power and reactive power supplied to the load are 0.50 and 0.30 respectively. Bus 1 is a slack bus. Use Gauss-Seidel method to determine the (i) voltage at bus 2, (ii) slack bus real and reactive powers, (iii) line flows,
TOPIC: Transmission Lines, Power Systems, and Powerplants:INSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:The per-phase constants of a 345-kV, three-phase, 150-km-long transmission line are resistance = 0.112/km, inductance-1.1 mH/km, and capacitance = 0.02 uF/km. The line supplies a 180-MW load at 0.9 power factor lagging. Using the nominal-m circuit, determine the sending-end voltage in kV. 351.2 349.3 348.7 350.8
a short three phase transmission line connected to 33kv 50 hertz generating station at starting and is required to supply a load of 10 MW at pointed start lagging power factor at 30 KV addresses in that is the minimum transmission efficiency is to be determined96% estimate the per face value of resistance and inductance of a line
the air-filled two-wire line has a characteristic impedance of 50 Ω and is operated at f = 3GHz .the load is ZL= 100 +j40Ω . for the line above, calculation ZL on the chart the line impedance 2.5 cm from the load , the admittance, the VSWR on the line, and distance from the load to the first voltage minimum and maximum.
A 220 kV, 50 Hz, three-phase transmission line is 60 km long. The resistance per phase is 0.15 ohms/km and the inductance per phase is 1.3 mH per km and the shunt capacitance is negligible. Use the short line model to determine; i) the voltage and power at the sending end ii) voltage regulation and efficiency when the line is supplying a three-phase load of 350 MVA, 220 kV at a power factor of 0.85 lagging.
1. Based on the exercise, what do you understood about STAR connection? 2. What are the relationships between the Line parameters and Phase parameters in Star Connection?
The length of a power transmission line is ℓ = 150 km, the unit effective resistance of the line is r = 0.06 Ω/km, x = 0.4 Ω/km and the admittance value of the line is y = j4.10-6 Siemens/km. The end-of-line voltage is 154 kV, the line-head voltage is 170∠10o kV. a) The characteristic impedance of the line b) The power drawn by the load according to the given values c) Calculate the maximum power that the line can transmit?
Estimate the distance over which a load of 15000 kW at 0·85 p.f. can be delivered by a 3-phase transmission line having conductors of steel-cored aluminum each of resistance 0·905 Ω/phase per kilometer. The voltage at the receiving end is to be 132 kV and the loss in transmission is to be 7·5% of the load.