Part A Determine the number of gallons of paint needed to paint the outside surface of the water-supply tank, which consists of a hemispherical bottom, cylindrical sides, and conical top. Each gallon of paint can cover 251 ft². (Figure 1) Express your answer to three significant figures and include the appropriate units. V = Submit 195| ΑΣΦ. 41 | vec My Answers Give Up ? gal

Part A Determine the number of gallons of paint needed to paint the outside surface of the water-supply tank, which consists of a hemispherical bottom, cylindrical sides, and conical top. Each gallon of paint can cover 251 ft². (Figure 1) Express your answer to three significant figures and include the appropriate units. V = Submit 195| ΑΣΦ. 41 | vec My Answers Give Up ? gal

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 26P: SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the...

See similar textbooks

Similar questions

A trapezoidal oil tank has the following dimensions: B1 = 8 3/4", B2 = 15 1/2", the height is 65/8" and it is 10 7/8" long. How many gallons of oil will it hold? (231 cu. in. = 1 gallon)
A tank contains ail sp. gr. 0.80, gasoline sp. gr. 0.90 and seawater sp. gr. 1.03. If the depths of the liquids are 0.5 m, 0.8 m and 1 m for oil, gasoline and seawater respectively. Find the pressure at a depth of 1.2 m. a. 28.124 Kpa b. 21.092 Kpa c. 16.04 Kpa d. 10.104 Kpa The answer for this is letter D which is 10.104 Kpa however I dont know the exact solution.
Q.1 Calculate Reynold’s Number if kinematic viscosity of a liquid is 0.001 m2/s , density is 500 kg/m3 flowing through dia of 10 mm with velocity of 30m/s?
Convert 800mm of a certain liquid with sg=1.25 to a)oil of specific gravity equal to 0.80 and b) water
Given: 50 cm/sec 7.48 gallons/ 1ft^3 Solve: gallons/hr
A liquid is flow throw Rotameter to a tank of size ( L x W x H ) and it is required to full the tank to level of H as shown in Figure . What time is required to full the tank by this liquid ? What time is required to drop the liquid in the tank to from level H to D by rectangular notch ?
A thin walled spherical tank is filled with water at a pressure of 4666 psig, the tank’svolume is then 805.407 in3. If the water is released from the tank, how many poundswill be collected at atmospheric pressure? Use 305 000 psi as an average value of bulkmodulus of elasticity
Hydraulics 6. Determine the Reynolds number of a 0.40 cubic meter per second oil of Gs=0.80 and an absolute viscosity of 0.025 Pa.s thru a 450 mm diameter pipe.
A container holds two layers of different liquids, one fluid having a specific gravity of 1.1 is 30cm deep and the other fluid having a specific gravity of 1.6 is 40cm deep. A solid cubical metal having an edge dimension of 18cm and specific gravity of 6.5 is submerged such a manner that half of the cube is on the top layer and the other half in the bottom layer of fluids with the square base of the cube horizontal. Help me compute the weight WCUBE of the cubical metal in newtons, compute the buoyant force BFCUBE in newtons acting on the metal object, and compute the tension T in newtons in the wire holding the cube to maintain its position. please draw a figure
2. What volume flow rate in gallons per minute of oil (sg = 0.80) is in the system?
Three pipes are connected in series. The first pipe has a diameter of 500 mm and a length of 600 m. The second pipe has a diameter of 400 mm and a length of 500 m. The third pipe has a diameter of 300 mm and a length of 200 m. Use f = 0.02 for all pipes. If Q=0.8 m^3/s, What is the equivalent diameter, in mm, of a single pipe having the same properties that could replace the three pipes? Round off to the neares whole number.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa Please answer with complete and detailed solutions. thank you. ASAP