Part A In the circuit shown in (Figure 1), find the magnitude of current in the upper branch. Express your answer in amperes. I = 0.2 A Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining Part B Find the magnitude of current in the middle branch. Express your answer in amperes. I = 0.8 A 1 of 1 Submit Previous Answers Request Answer 2.00 N 10.00 V 3.00 N а X Incorrect; Try Again; 2 attempts remaining 1.00 N 5.00 V, 4.00 N Part C Find the magnitude of current in the lower branch. b Express your answer in amperes. 10.00 N I = 0.600 A

Part A In the circuit shown in (Figure 1), find the magnitude of current in the upper branch. Express your answer in amperes. I = 0.2 A Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining Part B Find the magnitude of current in the middle branch. Express your answer in amperes. I = 0.8 A 1 of 1 Submit Previous Answers Request Answer 2.00 N 10.00 V 3.00 N а X Incorrect; Try Again; 2 attempts remaining 1.00 N 5.00 V, 4.00 N Part C Find the magnitude of current in the lower branch. b Express your answer in amperes. 10.00 N I = 0.600 A

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter23: Special-purpose Outlets—electric Heating, Air Conditioning

Section23.1: Electric Heat

Problem 17R: Electric heating cable embedded in plaster, or sandwiched between layers of dry wall, creates heat....

See similar textbooks

Similar questions

Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C what is the answer? VD?
1.A. You've assembled the following components to join two copper conductors: a mould, powdered copperoxide, powdered aluminum, and an igniter. With these components, which of the following processes willyou use to connect the conductors?A. Exothermic weldingB. Irreversible compression groundingC. Mechanical groundingD. Thermal cycling 1.B. Two electricians are discussing voltage ratings. Electrician A says that a motor that's installed 40 feetfrom a power source will show a lower applied voltage than a motor that's installed 20 feet from the samepower source. Electrician B says that an exact voltage of 240 V must be applied to a motor that's rated at240 V. Who is correct?A. Neither Electrician A nor Electrician B is correct.B. Only Electrician A is correct.C. Only Electrician B is correct.D. Both Electrician A and Electrician B are correct.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: • A positive-sequence balanced three-phase wye-connected source with a phase voltage of 120 V supplies power to balanced wye-connected load. The per phase load impedance is 40+j10Ω. Determine the line currents in the circuit if <Van=0°.
Thermal question. A system has two thermal layers. The first layer has a Rth 0.5 K/W, and Cth 0.8 J/K, and the second layer has a Rth 0.2 K/W, and Cth 0.4 J/K. The ambient air temperature is 50 °C. The power dissipation in the system is 100 W. What is the temperature of the second layer 5 s after a system is switched off? Please do not include any units in your answer.
Voltage Drop! Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C. what is the Voltage Drop ? Answer?
1.a. Section 300.15(C) requires a fitting to be installed on each end of a conduit or tubing being used toprovide support or protection to protect the cable fromA. hazardous vapors.B. direct sunlight.C. abrasion.D. extreme heat or cold.1.b. Typically, a/an _______ is a better electrode than a ground rod because it provides a greater surface areafrom which the electrons can be dissipated.A. continuous grounding conductorB. clamp-on ground resistance meterC. rebarD. OCPD
An underground paper -insulated, copper conductor cable is used to supply a 2 MVA 11 kV transformer from a utility supply which is 3 km away. The depth of burial of the cable is 1.5 m. Ground thermal resistance is 2.5 Km/W. The ground temperature is 30°C and there are no other cables in the trench.calculate a) full load current and cable size to limit voltage drop below 2.5%
A computer's power supply converts mains AC to low-voltage regulated DC power for the internal components of a computer. You are building a new computer. You are deciding which type of power supply to install. Which of the following definitions BEST describes a valid type of power supply? Correct Answer: A single-rail power supply provides one rail (PCB trace). This provides the best safety for the computer by providing a single point of shutdown in the event of a short circuit. Correct Answer: A single-rail power supply provides one rail (PCB trace) used to always provide equal wattage to all devices attached to the power supply. Correct Answer: A dual-rail power supply provides separate rails (PCB traces) used to provide equal wattage to the devices attached to each rail. Correct Answer: A dual-rail power supply provides separate rails (PCB traces) used to balance the power load between multiple circuits, which prevents any one circuit from becoming overloaded.
QUESTION 11 What is the ampacity of 3/0 AWG Copper THWN if there are 7 of them that are considered current carrying conductors in a conduit and the ambient temperature is 79 Degrees F? The conduit is strapped to a ½" piece of plywood laying on the roof. A 81.2 B 105 C 114.8 D 140
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places • If Vab = 480V in a balanced Y-connected three-phase generator, find the phase voltages, assuming the phase sequence is a. abc, b. acb
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: • A 300V(line) 3-phase supply feeds a star-connected load consisting of non-inductive resistors of 15, 6 and 10Ω connected to the R, Y and B lines, respectively. The phase sequence is RYB. Calculate the voltage across each resistor.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places • A positive-sequence three-phase balanced wye voltage source has a phase voltage of Van=100 <20° V. Determine the line voltages of the source.