Part A The beam is supported by a pin at A and a short link BC. If P = 12 kN , determine the average shear stress developed in the pins at A, B, and C . All pins are in double shear as shown, and each has a diameter of 20 mm. (Figure 1)

Part A The beam is supported by a pin at A and a short link BC. If P = 12 kN , determine the average shear stress developed in the pins at A, B, and C . All pins are in double shear as shown, and each has a diameter of 20 mm. (Figure 1)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.9.11P: Derive the following formula for the distance e from the centerline of the wall to the shear center...

See similar textbooks

Related questions

Q: 75 mm When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of…

A: Given data: The applied force, P = 750 N. The shear stress in the pin, τ = 40 MPa. Draw the…

Q: A structural steel bar with a 25 mm x 75 mm rectangular cross section is subjected to an axial load…

Q: Question 4: Two wrenches are used to tighten the pipe. If the pipe is made from a material having an…

Q: Link AB, of width b = 40 mm and thicknesst = 5 mm, is used to support the end of a horizontal beam…

Q: 70 4 in 3.5 in. | 30° 0.5-in dia. Detail at A 12 ft

A: given; load(P)=28.96KNAC=12ft =3.65mdiameter(d)=20.75mmlets take horizontal reaction force at…

Q: Rigid beam AB rests on the two short posts shown in Fig. 4–7a. AC is made of steel and has a…

Q: The axial stresses are 12 MPa C in the wood post B and 150 MPa T in the steel bar A as shown below.…

A: Answer: (a) The load P is 70875 N. (b) The minimum diameter for pin C is 22.62 mm. (c) The minimum…

Q: he cross section of a reinforced concrete beam is shown below. It has a modular ratio of 15. If the…

A: Givenm=15σcb=6N/mm2σst=120N/mm2

Q: Q - (A) // The figure A shown that the beam which is supported with a pin at A and a roller at B,…

Q: Two vertical forces, each of magnitude P= 26 kips, are applied to a beam of the cross section shown.…

Q: 4. The rigid beam AB is supported by steel (E = 200 GPa, v = 0.3) rods AC and BD of identical…

Q: The wide-flange beam is subjected to the P = 54 kN force. Determine the principal stresses in the…

A: Drawing the FBD of the given schematic diagram,

Q: 6. The A-frame is loaded by two concentrated forces as shown in the figure. The pins at B and C have…

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P= 5…

A: given: P = 5 kip

Q: 1 in. M 8 in. 1 in. 6 in. 1 in. 1 in. The box-beam above is subjected to a single positive bending…

A: Given: Stress distribution for the given cross-section:

Q: The figure shows a cross section of simply supported beam with a uniformly distributed load of 4.8…

Q: PROBLEM 1. The AD beam shown in the figure is supported by BC rod with pin connections. The pin at…

Q: 4.00kips Ib 600 ft Problem 3. Pin B acts in double shear and has diameter d=3/4 in. Pins are…

A: Given data: The diameter of the pin, dB=34 in. The failure stress is, τfailure=12000 psi. Draw the…

Q: For the beam shown, determine the average shear stress and shear strain in bolts at joints A and B.…

Q: Two bars are connected by means of a rivet of diameter 5 mm as shown in fig. below. Determine the…

Q: Determine Poisson's ratio for a cast iron that has a modulus of E= 12× 106 psi and a shear modulus…

A: Given data : The value of modulus of elasticity=12×106 psi The value of shear modulus=4.8×106 psi…

Q: A simple supported beam with the cross-section shown below supports vertical loads and has a maximum…

A: A1=2×20×4 =160mm2A2=2×52×6 =624mm2A3=40×4 =160mm2 centroid y =A1Y1 +A2Y2 +A3Y3A1+A2+A3 y =160×42…

Q: Member AB has a uniform rectangular cross section of 10 x 24 mm. For the loading P shown, a) Find…

A: GIVEN :-α=45°P=8KNdimension of member AB : 10×24=240 mm2SOLUTION :-a) taking moment about…

Q: 1. In the figure, assume that a 20-mm diameter rivet joins the plates which are 100 mm wide. a. If…

A: P= Stress x Arivets P=80[1/4 π (202)] P=8000 π N From bearing of plate material:P=σbAb 8000 π = 140…

Q: A 12 mm The steel shaft is made from two segments: AC has a diameter of 12 mm, and CB has a 125 mm D…

A: According to the information we have a steel shaft with two segments AC and CB torque on the shaft…

Q: 1. Determine the stresses for a square stress element on top of CD at point D. The stress element is…

Q: A steel plate of dimensions 2.5 × 1.2 × 0.1 m is hoisted by a cable sling that has a clevis at each…

Q: The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam…

A: ◆ Take the moment of forces about point C to determine the compressive force in the strut AB. ◆ The…

Q: The beam shown is made from two boards. Determine the maximum load (w) that can be applied if the…

A: Shear stress acts tangentially to any surface. The applied shear force is distributed as shear…

Q: QUESTION 1) A channel type cross-section is subjected to the compression force P-20 kN at the point…

A: The section is as shown below, The area of the section is, A1=20×5=100 cm2A2=20×5=100…

Q: 1. A force of P: = 800 N is exerted on control arm BC, which is securely attached to the solid 30 mm…

Q: Problem 1 Please choose the correct answer and also write down your solution. (1) The section…

A: shear stress distribution due to shear force alone is parabolic shear stress τ=F2Id24-y2maximum…

Q: Q1: At a certain section, beam has the cross-section shown in Figure (1) below. The beam is simply…

Q: The simply supported joist is used in the construction of a floor for a building. In order to keep…

A: Understand due to symmetry of the beam the reactions offered by the supports will be equal and…

Q: A cantilever wood beam consists of eight 2 in. thick planks glued together to form a cross section…

Q: Problem 3 Consider the cross section shown below. Knowing that the vertical internal shear force at…

A: Shear stress at a and b.

Q: Example 3 Determine: a. The shear stress at point B on the web of the cantilevered strut at section…

A: Answer: (a) The shear stress at point B: 8.81735 MPa (b) The maximum shear stress: 9.70434 MPa

Q: 5. The vertical shear force acting on the cross section shown is 1800 lb. Determine the shear stress…

Q: A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is…

Q: An overhanging beam of channel section supports a uniformly distributed load of 10 kN/m and a…

A: Given: The UDL, w = 10 kN/m The concentrated load, P = 20 kN

Q: The cantilever beam is subjected to a concentrated load of P-32 kips. The cross-sectional dimensions…

Q: Two vertical forces, each of magnitude P= 14 kips, are applied to a beam of the cross section shown.…

A: The question is related to the normal bending stresses produced in the beam due to bending only. The…

Q: Q8(0: For the truss shown in the Figure, if the diameter of pins at A and G are 3 in and 2 in,…

A: The stresses are to be calculated in support pin and members of truss. First the reaction forces are…

Q: Q70: For the truss shown in the Figure, if the diameter of pins at A and E are 60mm and 80mm,…

Q: Link AB, of width b = 40 mm and thickness t = 5 mm, is used to support the end of a horizontal beam…

A: Given b = 40 mm t = 6 mm Calculate the Load P=σ×A=0.04×0.006×80×106=19200 N

Q: SIMPLE STRESSES В 1. Rod AB carries 500 kg cylinder at B, and it is supported by a hinge at A.…

A: Given: The mass of cylinder, m= 500 kg The maximum shear strength of bolt at A, τ = 40 MPa

Q: typical method of temporarily securing a steel beam onto a column is by using a seat angle with…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

100%

Part A
The beam is supported by a pin at A and a short link BC.
If P = 12 kN , determine the average shear stress developed in the pins at A, B, and C. All pins are in double shear as
shown, and each has a diameter of 20 mm
(Figure 1)
Enter your answers separated by commas.
vec
TA, TB, TC =
MPа
Figure
< 1 of 1
Submit
Request Answer
Provide Feedback
Ne
0.5m
1m
1.5 m
1.5 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the maximum tensile, compressive, and shear stresses acting on the cross section of the tube at point A of the hitch bicycle rack shown in the figure. The rack is made up of 2 in. x 2 in. steel tubing which is 1/8 in. thick. Assume that the weight of each of four bicycles is distributed evenly between the two support arms so that the rack can be represented as a cantilever beam (ABCDEF) in the xy plane. The overall weight of the rack alone is W = 60 lb directed through C, and the weight of each bicycle is P = 30 lb.
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
The shear stresses t in a rectangular beam arc given by Eq. (5-43): in which Fis the shear force, / is the moment of inertia of the cross-sectional area, /lis the height of the beam, and i] is the distance from the neutral axis to the point where the shear stress is being determined (Fig. 5-32). By integrating over the cross-sectional area, show that the resultant of the shear stresses is equal to the shear force V.
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A copper bar with a square cross section is inserted into a square rigid tube as shown in the figure. The length of the copper bar is 1.2 m and the area of the cross section is 300 mm2. The bar is subjected to a force P that applies a uniformly distributed pressure to the copper. Calculate the force P if the longitudinal displacement of the bar is 2 mm. Assume that the modulus of elasticity of the bar is E = 110 GPa and Poisson’s ratio is v = 0.33. Disregard friction between the copper and the rigid tube.
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
Determine the shape factor f for a cross section in the shape of a double trapezoid having the dimensions shown in the figure. Also, check your result for the special cases of a rhombus (b1= 0) and a rectangle (b1= b2).
A flexible connection consisting of rubber pads (thickness f = 9 mm) bonded to steel plates is shown in the figure. The pads are 160 mm long and SO mm wide. (a) Find the average shear strain yaiTi in the rubber if the force P = 16 kN and the shear modulus for the rubber is G = 1250 kPa. (b) Find the relative horizontal displacement 3 between the interior plate and the outer plates.
The cross section of a slit square tube of constant thickness is shown in the figure. Derive the following formula for the distance e from the corner of the cross section to the shear center S: e=b22