Two vertical forces, each of magnitude P= 26 kips, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 8 in. 1 in. 1 in.→ 6 in. 1 in. 4 in. P D 60 in. 20 in. 20 in. The maximum tensile stress is |ksi. The maximum compressive stress is ksi.

Two vertical forces, each of magnitude P= 26 kips, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 8 in. 1 in. 1 in.→ 6 in. 1 in. 4 in. P D 60 in. 20 in. 20 in. The maximum tensile stress is |ksi. The maximum compressive stress is ksi.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.4P: .4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the...

See similar textbooks

Similar questions

A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an internal pressure of 3.0 MPa. Determine the thickness of tank (nearest mm) if the following stresses are not to be exceeded: tangential stress of 45 MPa and longitudinal stress of 30 MPa. and also show the free body diagram
The stresses shown act at a point in a stressed body. Assume stress magnitudes of Sx = 13,300 psi, Sy = 7,750 psi, and β=25∘. Determine the normal and shear stresses at this point on the inclined plane shown.
A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.
Two vertical forces are applied to the beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam.
!! Show Complete & Detailed Solution w/ FBD !!From the figure shown, the diameter of each segment is indicated. Determine the average normal stress developed at points.a. Ab. Bc. C.
In a 2.5 cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the section modulus and The base and height of the beam if the base is 75% of its height mm.
A thick cylinder internal diameter 240mm external diameter 240mminternal diameter ‘D’ is subject to external pressure of 40MPa. Determine the diameter‘D’ if the minimum hoop stress in the cylinder is not to exceed 200MPa in mm.
Two vertical forces, each of magnitude P = 22 kips, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. The maximum tensile stress is ksi. The maximum compressive stress is ksi.
A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal pressure of 15 N/mm2 and an external pressure of 5 N/mm2. Determine and sketch curves showing the distribution of the radial and circumferential stress across the section using Lame’s equations.
Show whether it is safe by calculating the stresses at point A according to the Tresca Criteria. (Diameter: 20 mm, σA = 320 MPa)
A prismatic bar with a length L = 3ft and cross- sectional area A= 8in2 is compressed by an axial centroidal load P= 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W=35", and show the stresses on a properly oriented stress element.