Part A The Concorde was a supersonic aircraft used for trans- Atlantic travel in the 1980s and 1990s, having a length of 61.6 m when sitting on the ground on a typical day when the temperature is 12.0 °C. The Concorde is primarily made of aluminum. In flight at twice the speed of sound, friction with the air warms the Concorde's skin and What is the temperature T of the Concorde's skin in flight? • View Available Hint(s) causes the aircraft to lengthen by 27.0 cm . (The passenger cabin is on rollers, so the airplane expands around the passenger cabin.) AZO Take the coefficient of linear expansion for aluminum to be a = 2.40x10-5 /°C. T = °C Submit

Part A The Concorde was a supersonic aircraft used for trans- Atlantic travel in the 1980s and 1990s, having a length of 61.6 m when sitting on the ground on a typical day when the temperature is 12.0 °C. The Concorde is primarily made of aluminum. In flight at twice the speed of sound, friction with the air warms the Concorde's skin and What is the temperature T of the Concorde's skin in flight? • View Available Hint(s) causes the aircraft to lengthen by 27.0 cm . (The passenger cabin is on rollers, so the airplane expands around the passenger cabin.) AZO Take the coefficient of linear expansion for aluminum to be a = 2.40x10-5 /°C. T = °C Submit

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.68P

See similar textbooks

Similar questions

Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the thickness of the hydrodynamic boundary layer at a distance 0.3 m from the leading edge of the surface.
A liquid (? = 850 kg/?3; ? = 1.7 × 10−1 Pa ∙ s) flows tangentially past a flat plate. If the free stream velocity is 2 m/s Question 1: what is the velocity 5 m downstream from the leading edge of the plateand 15 mm away from the plate. Question 2: if that plate is 10 m long and 3 m wide. Determine the drag force on the plate when liquid flows over both sides of the plate. (just only answer Question 2)!!!
1.)A semi-cylindrical concrete structure having a radius of 5 m and length of 3 m is rested on ground. Wind (air having a density ρ=1,2 kg/m3 ) at a free-sream speed of 3 m/s with an atmospheric pressure of 100 kPa far upstream the structure blows over the structure. The air entrance to the structure is at ground level corresponding to the forward stagnation point . Since the magnitude of minimum pressure is acting on the top of the structure determine the magnitude of lift force due to the pressure difference in vertical direction .Assume flow potential ANSWER: 648 N
What is the Mach Number of an aircraft flying at 3000 ft with 450 m/s?What is the aspect ratio of a tapered wing with span of 8m and a planform area of 20 m^2
Consider a rectangular wing with a NACA 23015 airfoil that has a maximum thickness of 2.7 ftand a wing span of 20ft if the freestream density, temperature and mach number are 1.22x10^-3 slugs/ft^3, 444 R and 0.2 respectively. Calculate the lift if the coefficient of lift is 0.8. English unit not metric
The drag coefficient of a car at the design conditions of 1 atm, 70°F, and 60 mi/h is to be determined experimentally in a large wind tunnel in a full-scale test. The frontal area of the car is 22.26 ft2. If the force acting on the car in the flow direction is measured to be 68 lbf, determine the drag coefficient of this car.
At subsonic speeds, how do the lift coefficient CL and drag coefficientCD for a wing vary with angle of attack α?
Consider the same Lockheed F-104 supersonic fighter shown, with the same flight conditions of Mach 2 at an altitude of 11 km. For these conditions the wing angle of attack is α = 0.035 rad = 1.98◦. Assume the chord length of the airfoil is 2.2 m, which is approximately the mean chord length for the wing. Also, assume fully turbulent flow over the airfoil. Calculate: (a) the airfoil skin friction drag coefficient, and (b) the airfoil wave-drag coefficient. Compare the two values of drag.
Consider a NACA 2412 airfoil at an angle of attack of 4 degrees. If the freestream Mach number is 0.72 determine the lift coefficient.
Air is flowing past a spherical ball. Is the lift exerted on the ball zero or nonzero? Answer the same question if the ball is spinning.
Given the following measurements of mean winds and temperature from a 200-m mast inNetherlands on a September night: Table 1. Measurements of mean winds and temperature from a 200-m mast in Netherlands ona September night. Question: Solve for the roughness parameter (zo) and friction velocity (U*)
Assume that a radioactive dust particle approximates asphere of density 2400 kg/m3. How long, in days, will ittake such a particle to settle to sea level from an altitude of12 km if the particle diameter is (a) 1 μm or (b) 20 μm?