I ReviewPart AThe two bars shown in the figure below (Figure 1) aremade of a material that has the stress-strain diagramshown. (Figure 2)If the cross-sectional area of bar AB is 2.4 in? and BC is 5.0 in?, determine the largest force P that can be supported before anymember fractures. Assume that buckling does not occur.Express your answer to three significant figures and include appropriate units.HAP =ValueUnitsSubmitRequest AnswerFigure1 of 2Provide FeedbackNext >4 ft3 ftP Pearson I ReviewPart AThe two bars shown in the figure below (Figure 1) aremade of a material that has the stress-strain diagramshown. (Figure 2)If the cross-sectional area of bar AB is 2.4 in? and BC is 5.0 in?, determine the largest force P that can be supported before anymember fractures. Assume that buckling does not occur.Express your answer to three significant figures and include appropriate units.HA?P =ValueUnitsSubmitRequest AnswerFigure2 of 2>Provide FeedbackNext >o (ksi)2520-15compression10ptension€ (10¬*) (in./in.)0.200.400,60 0,75P Pearson

Answered: Image /qna-images/answer/951146f2-ad54-4729-a76c-ad67b352f227.jpg

Part A The two bars shown in the figure below (Eigure 1) are made of a material that has the stress-strain diagram shown. (Figure 2) If the cross-sectional area of bar ABis 2.4 in? and BC is 5.0 in?, determine the largest forçe P that can be supported before any member fractures. Assume that buckling does not occur. Express your answer to three significant figures and include appropriate units. P = Value Units Submit Request Answer Figure < 1 of 2 > Provide Feedback Next > 3 ft

Part A The two bars shown in the figure below (Eigure 1) are made of a material that has the stress-strain diagram shown. (Figure 2) If the cross-sectional area of bar ABis 2.4 in? and BC is 5.0 in?, determine the largest forçe P that can be supported before any member fractures. Assume that buckling does not occur. Express your answer to three significant figures and include appropriate units. P = Value Units Submit Request Answer Figure < 1 of 2 > Provide Feedback Next > 3 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A bar with a square cross-section measuring 1.25 cm on a side is made of a material with yield strength of 310 MPa, and ultimate tensile strength of 515 MPa. Determine the maximum load the bar can withstand without fracture. Give your answer in N.
Define Young's Modulus, Hooke's Law, Modulus of Resilience, Fracture Strength & True Stress Vs Engineering Stress.
A cylindrical steel pressure vessel D-575 mm in diameter with a wall thickness of 5 mm is subjected to an internal pressure of 3 MN/m². Calculatea- the tangential and longitudinal stresses in the steel.b- To what value may the internal pressure be increased if the stress in the steel is limited to 80 MN/ m²?c-If the internal pressure were increased until the vessel burst, sketch the type of fracture that would occur
A horizontal steel I – beam of cross-sectional area 0.041m2 is rigidly connected to two vertical girders. If the beam was installed when the temperature was 300C, what stress is developed in the beam when the temperature drops to - 300C? (b) Is the ultimate strength of the steel exceeded? (c)What stress is developed if the beam is concrete and has a cross- sectional area of 0.13m2 ? Will it fracture?
1. In the nominal stress-strain diagram (Figure 1), write down the names and meanings of points 1, 2, 3, and 4.2. Explain how to find the 0.2% offset yield strength, and explain the% elongation and% reduction in cross-sectional area.3. After explaining the difference between the true stress/strain and the nominal stress/strain, show the true stress-strain diagram for the nominal stress-strain diagram (Figure 1) to correspond points 1, 2, 3, and 4.
1. A cylindrical steel specimen, with an initial diameter of 7mm, has elongated by 40% at the point when it starts to neck down. The load at the start of necking is 35 kN. What is the true stress at the ultimate tensile stress? The answer is 1273, but I'm not getting that. Please answer soon and neatly. Don't copy or I will dislike u many.
A small room is made up ofrectangular metal bars. One bar has a width of 10 mm and would beable to withstand a maximum compressive stress of 20 MPa.i. Prove that, the minimum breadth of this bar can withstand a burdenedwith a force of 3 KN.ii. If the bar in question is 2 m long and decreases in length by 0.25 mmwhen a force is applied, then show that a percentage strain can beobtained.iii. What would be its Modulus of Elasticity, E?
A cylindrical steel pressure vessel ___171__ mm in diameter with a wall thickness of 5 mm is subjected to an internal pressure of 3 MN/m². Calculate a- the tangential and longitudinal stresses in the steel. b- To what value may the internal pressure be increased if the stress in the steel is limited to 80 MN/ m²? c-If the internal pressure were increased until the vessel burst, sketch the type of fracture that would occur
How are stress and strain distributions calculated within the structure?
A tie rod made of quenched and tempered 4340 steel is used as a critical linkage in an industrial apparatus. The rod is subjected to an alternating cyclic tensile/compressive stress from 550 MPa to -550 MPa. An inspection of the rod revealed a 3.5 mm deep edge crack on the surface of the rod. Please answer the following question for the rod given the properties in the table and curve below and fracture toughness of 55 MPa√m. (NOTE: Y=1.12 for edge crack and use “a” not “2a” for the length of the crack) 1. At the given crack size and tensile loading would the rod undergo instantaneous fast fracture, assuming plane strain conditions? Show calculations to back up your conclusions.
A tie rod made of quenched and tempered 4340 steel is used as a critical linkage in an industrial apparatus. The rod is subjected to an alternating cyclic tensile/compressive stress from 550 MPa to -550 MPa. An inspection of the rod revealed a 3.5 mm deep edge crack on the surface of the rod. Please answer the following question for the rod given the properties in the table and curve below and fracture toughness of 55 MPa√m. (NOTE: Y=1.12 for edge crack and use “a” not “2a” for the length of the crack) 1. What is the minimum crack size that would cause instantaneous fast fracture at the current maximum axial tensile loading, assuming plane strain conditions apply? If the resolution limit of the flaw detection apparatus were 1.5 mm, would this flaw be subject to detection? Show calculations to back up your conclusions.
A tie rod made of quenched and tempered 4340 steel is used as a critical linkage in an industrial apparatus. The rod is subjected to an alternating cyclic tensile/compressive stress from 550 MPa to -550 MPa. An inspection of the rod revealed a 3.5 mm deep edge crack on the surface of the rod. Please answer the following question for the rod given the properties in the table and curve below and fracture toughness of 55 MPa√m. (NOTE: Y=1.12 for edge crack and use “a” not “2a” for the length of the crack) 1. Given the S-N curve for 4340 steel, is there an endurance limit? If so, what is the stress value for the endurance limit? 2. If there were no cracks and the stress on the rod still alternated from 550 MPa to -550 MPa with mean stress of zero, what would be the cycles to failure?