Part A When y is zero, the springs sustain a force of 54 lb. (Figure 1) Determine the magnitude of the applied vertical forces F and -F required to pull point A away from point Ba distance of y = 1.5 ft. The ends of cords CAD and CBD are attached to rings at C and D. Express your answer to two significant figures and include the appropriate units. Figure 1 of 1 ? F = Value Units Submit Request Answer www k- 40 Ib/ft 2ft O 2 ft k- 40 Ib/ft www Provide Feedback Next >

Part A When y is zero, the springs sustain a force of 54 lb. (Figure 1) Determine the magnitude of the applied vertical forces F and -F required to pull point A away from point Ba distance of y = 1.5 ft. The ends of cords CAD and CBD are attached to rings at C and D. Express your answer to two significant figures and include the appropriate units. Figure 1 of 1 ? F = Value Units Submit Request Answer www k- 40 Ib/ft 2ft O 2 ft k- 40 Ib/ft www Provide Feedback Next >

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.1P: Bar AB of negligible weight is supported by a ball-and-socket joint at B and two cables attached at...

See similar textbooks

Similar questions

The ABD bracket is supported by a pin at A and the cable DE. Determine the internal forces immediately to the left of the load.Template: (On CD) F= 270 N; M=43.2 N.m; V = 90 N
The pin at O can support a maximum force of 3.5 kN. What is the corresponding maximum load L which can be applied to the angled bracket AOB? A. 0.541 kN C. 2.632 kN B. 1.676 kN D. 3.091 kN
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown inFigure: Q 4(b). Assume flange at point B always remains straight. (i) Sketch free body diagram (FBD) of segment AB and BC.(ii) Determine the magnitude of the force P if tensile stress in rod AB is equal to magnitudeof compressive stress in rod BC.
One end of a post weighing 400 Nand with height h rests on a roughhorizontal surface with ms = 0.30.The upper end is held by a ropefastened to the surface and makingan angle of 36.9° with the post. A horizontal force F isexerted on the post as shown. (a) Ifthe force F S is applied at the midpointof the post, what is the largest value it can have without causing the postto slip? (b) How large can the force be without causing the post to slip ifits point of application is 6/10 of the way from the ground to the top of thepost? (c) Show that if the point of application of the force is too high,the post cannot be made to slip, no matter how great the force. Find thecritical height for the point of application.
PROBLEM 1: Determine the tension in each cable and the components offorce reaction at D needed to support the load. Required: 1. Find Dx (Answer: 1039.230 N), Dy (Answer: 0 N) and Dz (Answer: 0 N) 2. Find Tension AB (Answer: 467.667 N) and Tension (Answer: AC 673.808)
Determine the tensile force in all cables. The plate weighs 150 kg. (Answer: FB = 858 N, FC = 0 and FD = 858 N)
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
A force of P=280 N is applied on semicircular rod at point B. Determine internal forces at point J if θ=30°. (draw free body diagram)
This structure is supported by a roller joint on the left and a pin joint on the top. Two loads, P have similar magnitudes of P = 650 N and the angle θ = 40°. The length L of both members is 1.5 m. The vertical load acts at the midpoint of the horizontal member. Solve for the reaction forces at the roller and pinned joints.
Fishing line with a tensile strength of 25 lbs is used at B to fasten 2 members together as shown. Find the maximum force F that can be supported, given:L1 = 2 in, L2 = 4 in L3 = 6 in, L4 = 5 in
Compute for the forces P and Q if the force in member CD is equal to 6000 lb (C) and in member GD is equal to 1000 b (C). Show solution to answer P = 5170 & Q = 370
a b c d F 5 m 1.5 m 2.1 m 2.4 m 26 kN The structure above is subjected to a load at point C. Using the table below, determine the forces acting at the support pins and at pin B on member ABC. Forces: (Denote tension forces with positive values; compressive forces with negative values.) FAX = ? FAY = ?