1. Cover page of the project 2. Table of the content 3. Abstract 4. Introduction 5. Detail machine selection, manufacturing sequence and fixture design 6. Possible futue improvement 7. Conclusion on this research 8. References (duing this research) Please select the necessary machines, define manufacturing sequences, and design supporting fixtures to keep manufactured part meeting following requirements: 1. Two flat sufaces being cut are parallel to the middle slot 2. Two Ø 0.4" thru holes are required to be made in its accurate location and be perpendicularto the middle slot 3. Two Ø 0,5" thru holes are made in the center line and center of two radius R 2.5" 2xR 2.5 Center line 2x00.4" thru - 2x0 0.5" thru 2 flat surfaces being cut au parallel to the middle slot

1. Cover page of the project 2. Table of the content 3. Abstract 4. Introduction 5. Detail machine selection, manufacturing sequence and fixture design 6. Possible futue improvement 7. Conclusion on this research 8. References (duing this research) Please select the necessary machines, define manufacturing sequences, and design supporting fixtures to keep manufactured part meeting following requirements: 1. Two flat sufaces being cut are parallel to the middle slot 2. Two Ø 0.4" thru holes are required to be made in its accurate location and be perpendicularto the middle slot 3. Two Ø 0,5" thru holes are made in the center line and center of two radius R 2.5" 2xR 2.5 Center line 2x00.4" thru - 2x0 0.5" thru 2 flat surfaces being cut au parallel to the middle slot

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer the two connected questions (Task A-1 and A-2). Provided in the last part are the guides and examples: The process for large-scale manufacture of paper has been largely unchanged for the last 125 years. The pulp and paper industry today is highly capital intensive, and there is an ongoing drive towards process integration, thereby increasing the efficiency of utilization of available process resources. This paper deals with the Kraft process (see Fig. 1) though the general principles described can be extended to other pulping processes. As shown in Figure 1, five water sinks and four water sources are considered for in-plant water reuse/ recycle. Prior to water reuse/ recycle, the network requires a freshwater flow rate of 36,400 tonne/day and generates 37,186 tonne/day of wastewater (sum of the individual sink and source flow rates in Table 1). The freshwater source that is available for service has an impurity concentration (chloride content) of 4.2 ppm, which is higher than…
A toy manufacturing uses 51030 rubber wheels per year for its popular dump truck series. The firm makes its own wheels, which it can can produce at a rate of 800 per day. The toy trucks are assembled uniformly ( at a constant rate ) over the entire year. Carrying cost is $ 1.50 per wheel per year. setup cost for the production run of the wheel is $ 47. The firm operatyes 243 days per year. Determine each of the following: 1-Optimal run size 2-Use your final answer from part 1 to determine minimum total annual cost for carrying and setup 3-Cycle time for the optimal run size 4-Run time
In a mechanical shopfloor it produce shafts, The shopfloor established with design capacity is 30 shafts per day and effective capacity is 20 shafts per day. Currently, the shop floor is producing 27 shafts per day. i. What is the shopfloor’s capacity utilization relative to both design and effective capacity? ii. What can you conclude?
Fig. 9-Displays a metal plate that has been cut to shape. Assume the density of the material is uniform. (Note: a=1m,b=6m,c=3med=3m.) (a) The coordinate xcm.(b) The coordinate ycm
What general trend did you observe from set-ups 3? Support your answer by using the data gathered.
Solve fast and correctly please by hand solution ??
Solve problem 17.5 but assume that defects never jam the workstations. Other data are the same 17.5 listed below (a) A 10-station assembly machine has an ideal cycle time of 6 sec. The fraction defect rate at each station is 0.005 and a defect always jams the affected station. When a breakdown occurs, it takes 1.2 min, on average, for the system to be put back into operation. Determine (a) the hourly production rate for the assembly machine, (b) yield of good product (final assemblies containing no defective components), and (c) proportion uptime of the system.
Solve problem 17.5 but assume that m = 0.5 for all stations. Other data are the same 17.5 listed below 17.5 (a) A 10-station assembly machine has an ideal cycle time of 6 sec. The fraction defect rate at each station is 0.005 and a defect always jams the affected station. When a breakdown occurs, it takes 1.2 min, on average, for the system to be put back into operation. Determine (a) the hourly production rate for the assembly machine, (b) yield of good product (final assemblies containing no defective components), and (c) proportion uptime of the system.
(USCS units) A turning operation is performed using a rake angle of 15°. Cutting speed = 200 ft/min, feed= 0.012 in/rev, and depth of cut = 0.100 in. The chip thickness ratio measured after the cut = 0.48. Determine (a) chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain (USCS units) The turning operation in the previous problem involves a work material whose shear strength = 52,000 lb/in2. Based on your answers to the previous problem, compute (a) shear force, (b) cutting force, (c) thrust force, and (d) friction force.
1- Consider the precedence relationship between the activities of an assembly line. Knowing that the cycle time (T) of the assembly line is 10, then: a) Show how the activities are assigned to the work station? b) Calculate line efficiency and smoothness indices.
Selasi wants a shaft of 5/8 inches diameter to be used in his design project of which he is considering a design factor of 3. He hopes to get the same shaft size or 11/16 inch diameter shaft in the market for his design. So he decided to send his apprentice, Amuzu to the market. Unfortunately, when Amuzu went to the market, there were 1⁄2 inch, 9/16 inch, 3⁄4 inch, and 7/8 inch sizes available in the first shop. Amuzu decided to buy the nearest shaft size in the first shop instead of checking in the other shops where he could have gotten either 5/8 inch or 11/16 inch sizes.a. Discuss the consequences Selasi would incur in his design project if Amuzu had bought 9/16 inch size shaft. b. Discuss the consequences Selasi would incur in his design project if Amuzu had bought 3⁄4 inch size shaft.
How might your machine or system be improved? What constraints might be involved in its design