Part B Determine the force in member CJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCJ = Value Submit μA Part C Request Answer Units ? Determine the force in member GJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.

Part B Determine the force in member CJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCJ = Value Submit μA Part C Request Answer Units ? Determine the force in member GJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel plate 2.5 m x 1.6 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the shear stress (MPa) in the 16 mm diameter pins through the clevis The correct answer is 45.33. Show solution.
DETERMINE THE INTERNAL FORCE OF MEMBER EF FROM THE FIGURE BELOW. Use four (4) decimal places during computation and two (2) decimal places for the final answer. Note: for compression, include a negative sign ( - ) and for tension, type answer as is.
an 8 m long steel is pinned at the top and fixed at the bottom. the column is provided with lateral support 3m from the top in the weak direction. the properties of the column section are as follows: ix = 178.1x10^6 mm^4 ly = 18.8x10^6 mm^4 a = 8129 mm^2 fy = 400 mpa a. what is the critical effective slenderness ratio? %3d %3d b. what is the buckling stress of the column? c. calculate the critical load pc in kn
Set P1 = 70 kN, P2 = 50 kN Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. a) Determine the force in member BG of the truss. b) Determine the force in member CD of the truss. c) Determine the force in member CF of the truss.
Engineering Mechanics DETERMINE THE INTERNAL FORCE OF MEMBER DF FROM THE FIGURE BELOW. Note: for compression, include a negative sign ( - ) and for tension, type answer as is. Use four (4) decimal places during computation and two (2) decimal places for the final answer.
Determine the maximum tensile stress and maximum compressive stress due to the load P acting on the simple beam AB (see figure). Data are as follows: P= 5.4 kN L=3.0 m d=1.2 m b=75 mm t_=25 mm h=100 mm h1=75 mm c1=62.5 mm c2=37.5 mm, and l= 3.3203x10⁶ mm⁴
Determine the vertical displacement of joint A. Each A992 steel member has a cross-sectional area of 400 mm2.
pls answer I'll rate Use virtual work method and determine the following unknowns on the truss system shown below. Use A = 500 mm2 and E = 200 GPa.a. Horizontal displacement of joint G due to the applied loads in mmb. Horizontal displacement of joint G considering that the top chord members experience 60 °C increase in temperature in mm. Use α = 10-6/°C
Determine the largest force P (kN), directed as shown in the figure that can be applied to the bracket if the allowable normal stresses on section A-B are 8 Mpa in tension and12 Mpa in compression. A119.15 B.79.44 C.18.64 d.14.31 answer:14.31
For the beam shown, determine the support reactions and draw the stress diagrams.shear and bending moment. EI is constant. Use the force method. I have a correct answer, it is: VA = 44.3 kN (↑); HA = 0 kN; MA = 34.3 kN.m (counterclockwise); VB = 38 kN (↑). I don't know how to get to this result, please show me how to get there step by step
A cantilever beam AB with a circular crosssection and length L = 750 mm supports a loadP = 800 N acting at the free end (see figure). Thebeam is made of steel with an allowable bendingstress of 120 MPa.(a) Determine the required diameter dmin (figurepart a) of the beam, considering the effect of thebeam’s own weight.(b) Repeat part (a) if the beam is hollow with wallthickness t =d /8 (figure part b); compare thecross-sectional areas of the two designs.
2.Determine the vertical displacement of joint A (a) if members AB and BC experience a temperature increase of ΔT = 200°F. Take A = 2 in^2 and E = 29(10^3) ksi. Also, a = 6.60 (10^-6)/°F. (b) if member AE is fabricated 0.5 in. too short. Include the effect of external forces in both cases.