3. The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the largest vertical load P that can be applied at C if the stress in the steel rod is limited to 45 MPa and the vertical movement of end C must not exceed 4.2 mm. Neglect the weights of the members. Write your final answer here: Largest vertical load P = A -1 m- 8.1 kN L = 2m A = 450 mm² E = 200 GPa -1.5 m-

3. The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the largest vertical load P that can be applied at C if the stress in the steel rod is limited to 45 MPa and the vertical movement of end C must not exceed 4.2 mm. Neglect the weights of the members. Write your final answer here: Largest vertical load P = A -1 m- 8.1 kN L = 2m A = 450 mm² E = 200 GPa -1.5 m-

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the vertical displacement of point C if the stress in the steel rod is limited to 29.76 ksi, X = 2.07 ft, and Y = 4.93 ft. Neglect the weights of the members. Round off the final answer to four decimal places.
Set P1 = 2.5 kN , P2 = 5 kN . (Figure 1) Determine all the member forces .
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
The girder of a simple log bridge supports a wheel load W acting at any position along the span. In addition, the weight of one log and the planks it supports is equivalent to a uniform load of 850 N/m acting on the log. Determine the maximum permissible wheel load W (in kN) based on an allowable shear stress of 0.75 MPa if the maximum shear stress on circular sections is 4/3 of the shear force divided by the cross-sectional Choices: 28.9 38.7 77.4 30.2 Note:please help me in this sample problem thank you
For the beam in question 1, determine the maximum bending and shear stressesat point C, at point P of the section. Represent the stress cube
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
Question ) Forces of F1=3 kN from point B in the z direction, F2=5 kN from point C in the z direction and F3=8 kN in the y direction are acting on the arm in the figure. The lengths of the arm are also given as L1=0.18 m and L2=0.17 m. It is desired to determine the stress state of point A on the a-a section taken from the arm. The radius r of the section is r=0.3 m and the shear modulus of the arm material is G=79 Gpa. According to this; Question 1-A) Find the shear stress due to the shear force at point A. (Write your result in MPa.Question 2-B) Find the shear stress due to the torsional moment at point A. (Write your result in MPa.Question 3-C) Find the total shear stress at point A. (Write your result in MPa)Question 4-D) Find the normal stress caused by the normal force at point A. (Write your result in MPa Question 5-E) Find the normal stress caused by the bending moment at point A. (Write your result in MPa.)Question 6-F) Find the total normal stress at point A. (Write your…
Determine the largest force P (kN), directed as shown in the figure that can be applied to the bracket if the allowable normal stresses on section A-B are 8 Mpa in tension and12 Mpa in compression. A119.15 B.79.44 C.18.64 d.14.31 answer:14.31