Part B Why is the energy gradient (i.e., the slope of the EL) larger in pipe 2 than in pipes 1 or 3? (<10 words) Part C Why are the EGL and HGL not parallel in this figure? (<10 words) E HGL EL Figure 8.29 (Finnemore and Franzini 2002) Ax Energy line, slope - S Hydraulic grade line, slope - S Bed slope L h₂ - Az Datum Figure 10.19 (Finnemore and Franzini 2002)

Part B Why is the energy gradient (i.e., the slope of the EL) larger in pipe 2 than in pipes 1 or 3? (<10 words) Part C Why are the EGL and HGL not parallel in this figure? (<10 words) E HGL EL Figure 8.29 (Finnemore and Franzini 2002) Ax Energy line, slope - S Hydraulic grade line, slope - S Bed slope L h₂ - Az Datum Figure 10.19 (Finnemore and Franzini 2002)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question: Cd= 1:0 = 0=1cm @ Derive The Equation Of Motion In Terms Of Height 2 Time For... Cd-1:0 D=I cm DeriDe the caationo Motirn in terms o height Tme Sor empgtng the tank Pen 1om 5m
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
Q2) i Neglecting minor losses in the pipe, determine the flows in the pipes and 0 the pressure heads at the nodes (kinematic viscosity= 1.13x104m?¥s) F E n I I 30 Data Pipe Ab BC O DE EF AF BE Lengeh (m) 600 600 200 600 600 200 200 Diameter (wm) 250 150 100 150 150 200 100 Roughness size of all pipes = 0.06 mm Pressure head elevation at A = 70 i o.d. Elevation of pipe nodes A 5 c D L ® 028 0 20 2 2
12. Find the discharge in each link using the given initial distribution by making 2 iterations and pressure drop between points O and C if they have the same elevation. B A 5 lt/min 5 7 lt/min с ? It/min 5 lt/min 20 D E KBC KCD-KAO-KOE KAB=KDE Koc=3KBC KAB=2KBC Koc=30 min²/dm5
5. Find the Total efongation of the bar below 12kN OKN 4KN 4KN+ 6KN LI 1.2 L3 L4
CID2 The hnt monent.at arma Q m at Oboch mainun and miimi 14 G
01) For the composite channel shown in Fig. The bed slope is (0.0003). Calculate: 1- The discharge of the channel 2- The required freeboard n-0.028 n-0.035 n-0,025 2.7m I.Im 1.5 6m 5m
for turbulent flow of fluid in a smoth Pipe, the following ve lation exists be tween the Friction factor Ce aned Reynolds num ber k =- 0.4+1.74 くReadce) Compute e for Re=105, decimol places. correct to six Determine the smallest positive roet of the equation - 0.0i t sin (0.573t)
Q1) Find The magnitude and direction of The Rorce exerted on The Blade shown bulowby aget, iE The slope angle (0= 120),The velocity V=Vz= 30m/sec, and The discharge (loLIsec)? Blade des Fx Fy
10.ln turbulent flow the losses are proportional to the velocity. hl&v O true O False
2. The flow from pipelines A to F is 300 lit/'s. Using a friction factor of 0.015 for all pipelines and with the properties listed below, compute a. the discharge at B b. the discharge at E c. the discharge at D d. headloss from 1 to 5 A Pipelines A TERREY B C D E 8 Length (m) 350 300 320 1100 550 650 Diameter (cm) 40 25 25 30 20 45
In Figure Q3 (a) frame ABC is being used to support a small rocket engine that is being tested, and is rigidly mounted at A. The rocket engine exerts a force P=20 kN at point C as shown. (a) Present shear and moment diagrams for frame ABC as shown in Figure Q3 (a), highlighting all key values. (b) Calculate the vertical displacement at point C on the frame. The flexural stiffness of the section used for the frame is El=4x107 Nm². Neglect axial and shear deformations. (c) Figure Q3 (b) shows the same frame and loading with the addition of a truss of length 1.0m between C and D. Calculate the load in truss CD if its stiffness is EA=4×108 N.