You need a capacitance of 55.0 μF, but you don't happen to have a 55.0 μF capacitor. You do have a 65.0 μF capacitor. Part A What additional capacitor do you need to produce a total capacitance of 55.0 μF? Express your answer with the appropriate units. C = Part B Submit Request Answer Value μÅ in parallel in series Submit Should you join the two capacitors in parallel or in series? Previous Answers ✓ Correct Units ?

You need a capacitance of 55.0 μF, but you don't happen to have a 55.0 μF capacitor. You do have a 65.0 μF capacitor. Part A What additional capacitor do you need to produce a total capacitance of 55.0 μF? Express your answer with the appropriate units. C = Part B Submit Request Answer Value μÅ in parallel in series Submit Should you join the two capacitors in parallel or in series? Previous Answers ✓ Correct Units ?

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter20: Electric Potential And Capacitance

Section: Chapter Questions

Problem 47P: According to its design specification, the timer circuit delaying the closing of an elevator door is...

See similar textbooks

Similar questions

Referring to Figure CQ21.4, describe what happens to the light-bulb after the switch is closed. Assume the capacitor has a large capacitance and is initially uncharged. Also assume the light illuminates when connected directly across the battery terminals.
According to its design specification, the timer circuit delaying the closing of an elevator door is to have a capacitance of 32.0 F between two points A and B. When one circuit is being constructed, the inexpensive but durable capacitor installed between these two points is found to have capacitance 34.8 F. To meet the specification, one additional capacitor can be placed between the two points. (a) Should it be in series or in parallel with the 34.8-F capacitor? (b) What should be its capacitance? (c) What If? The next circuit comes down the assembly line with capacitance 29.8 F between A and B. To meet the specification, what additional capacitor should be installed in series or in parallel in that circuit?
When discharging a capacitor, as discussed in conjunction with Figure 21.39, how long does it take for the voltage on the capacitor to reach zero? Is this a problem?
Check Your Understanding In an RLC circuit, L = 5.0 mH, C=60F , and R=200 . (a) Is the circuit under damped, critically damped, or overdamped? (b) If the circuit starts oscillating with a charge of 3.0103C on the capacitor, how much energy has been dissipated in the resistor by the time the oscillations cease?
A 20.0 HZ, 16.0 V source produces a 2.00 mA current when connected to a capacitor. What is the capacitance?
What total capacitances can yon make by connecting a 5.00F and a 8.00F capacitor?
(a) What is the potential difference going from point a to point b in Figure 21.47? (b) What is the potential difference going from c to b? (c) From e to g? (d) From e to d?
(Indicates a review question, which means it requires only a basic understanding of the material to answer. Questions without this designation typically require integrating or extending the concepts presented thus far.) . Describe Ohm’s law.
Repeat the calculations of the previous problem for a proton with the same kinetic energy.
A 165F capacitor is used in conjunction with a dc motor. How much energy is stored in it when 119 V is applied?
Why does the labeled capacitance of the capicitor is the same with the computed actual capacitance? What makes them have the same value?
A parallel plate capacitor has surface dimension of 40.0 cm x 20.0 cm. The capacitor is connected to a dc power supply of 50.0 V and a material with = 200 is inserted in between the plates. If the capacitance of the capacitor is 18 F, find a. the pate separation, d in meterb. the energy density of this capacitor, u in Joule per cubic meter