Please answer this question. I have also added "Lab 5 To-do Test 1" below. //LAB5 To-do TEST1: Change this code to implement the behavior described in the prelab section "Programming the Stepper Motor" //Enable this code to test the stepper motor separately Serial.println("Turning clockwise"); //output message to serial monitor steppermotor.setSpeed(60); //set speed to make 20 rotations per minute (each rotation takes 2 seconds) steppermotor.step(300); //rotate clockwise by 300 steps (5 revolutions since STEPS is 60 //END TEST1 Prelab item #1:Locate the code inModify the current code in this section and create a test code so that the motor behaves in the followingecen100lab_remote_stepper.inofile labeled "LAB5 To-do TEST1".manner:●●●●●●Set the speed to faster than currently specified (i.e. faster than 30 revolutions per minute)Rotate the shaft for 3 full revolutions counter clockwise.Output to the Serial Monitor the message "Done counter clockwising!".Wait for 3 seconds.Set the speed to slower than currently specified (i.e. slower than 30 revolutions per minute)Rotate the shaft 5 full revolutions clockwise.Output to the Serial Monitor the message "Done clockwising!".Wait for 2 seconds.Output to the Serial Monitor the message "And again!”.The motor movement repeats these steps until terminated (should be automatically done since this is inthe loop() portion of the code).Make your modifications to the ecen100lab_remote_stepper.ino file and also copy the code inthe box below:

The given code for the programming of the stepper motor is shown below.1//Enable this code to test…

Please answer this question. I have also added "Lab 5 To-do Test 1" below. //LAB5 To-do TEST1: Change this code to implement the behavior described in the prelab section "Programming the Stepper Motor" //Enable this code to test the stepper motor separately Serial.println("Turning clockwise"); //output message to serial monitor steppermotor.setSpeed(60); //set speed to make 20 rotations per minute (each rotation takes 2 seconds) steppermotor.step(300); //rotate clockwise by 300 steps (5 revolutions since STEPS is 60 //END TEST1

Please answer this question. I have also added "Lab 5 To-do Test 1" below. //LAB5 To-do TEST1: Change this code to implement the behavior described in the prelab section "Programming the Stepper Motor" //Enable this code to test the stepper motor separately Serial.println("Turning clockwise"); //output message to serial monitor steppermotor.setSpeed(60); //set speed to make 20 rotations per minute (each rotation takes 2 seconds) steppermotor.step(300); //rotate clockwise by 300 steps (5 revolutions since STEPS is 60 //END TEST1

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter13: Heating Control Devices

Section: Chapter Questions

Problem 1RQ

See similar textbooks

Similar questions

TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:In hazardous locations, the use of non-metallic conduit shall be permitted provided it is buried NOT less than ___________ blow the earth level. 400 mm 600 mm 1000 mm 500 mm
explain your steps
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:Two lamps are hung at a height of 9 m from the floor level. The distance between the lamps is one meter. Lamp one is of 500 candela. If the illumination on the floor vertically below this lamp is 20 lux, find the candle power of lamp number two. 570 candela 1140 candela 1710 candela 2280 candela
What type is a suitable electrical vehicle based on power systems and machines for human purposes.Prove your answers with block diagram
Please explain all your steps Thanks!
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: • A 3 phase, 4-wire, 400V symmetrical system supplies a Y-connected load having the following branch impedances: ZR=100 Ω, Zy=j10Ω and ZB=j10Ω Compute the values of load phase voltages and currents and neutral current. Phase sequence is RYB. How will these values change in the event of an open in the neutral wire?
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICSTOPIC: TRANSFORMERS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. ILLUSTRATION (Required).4. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible5. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:A 2300/230-volt distribution transformer is tested for polarity. If 118 volts is impressed across high-side terminals, what will the voltmeter register if the polarity is additive and subtractive?
1. Question text In solar module, minimum value of shunt resistance could be 300 Ohm. Select one: True False
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:A lamp of 500 cd is placed at the center of a room, 20m x 10m x 5m. Calculate the illumination (in lux) for each corner of the floor. 0.98 0.78 0.81 0.83
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you! 2. GIVEN.(include symbols and units) 3. REQUIRED/FIND/MISSING (with symbol/s) 4. ILLUSTRATION (Required). 5. STEP-by-STEP SOLUTION with Formulas and Symbols. No Shortcut, No skipping, and detailed as possible 6. FINAL ANSWERS must be rounded up to three decimal places PROBLEM: • A 3-phase, 4-wire, 380V supply is connected to an unbalanced load having phase impedances of ZR=(8+j6)Ω, Zr=(8-j6)Ω and ZB=5 Ω. Impedance of the neutral wire is ZN=(0.5+j1)Ω. Ignoring the impedances ofline wires and internal impedances of the emf sources, find the phase currents and voltages of the load.
Answer the following a) Explain the term “suppressed demand “, and give THREE instances in which suppressed demand occurs in a distribution system. b) Electricity demand is affected by a number of economic determinants. Mention any FOUR of such economic factor. c) Long-term forecasting of electrical load is associated with a high degree of uncertainties. Mention any THREE reasons or causes of this uncertainty. d) Give any FIVE drivers or factors that affect total load demand or electricity consumption. Please answer all, I prefer it all answered
Please help me solve no. 1 below. Please provide a clear and readable solution. Thanks in advance!!! The course subject is Feedback and Control System. NOTE: The lesson is ROTATIONAL MECHANICAL SYSTEMS.