Express the answers in solution in 2 decimal places. Thank you Please refer to the figure shown below. If P is equal to 6,720 lb., and ifall the rods have a cross-sectional area to be 0.4 sq. in. Explain whythe set-up will fail or will not fail if the allowable stresses in Steel is120MP%; 90MPa in Alumimun; and 100Mpa in Bronze. As the civilengineer of the project, if the set-up fails, provide a recommendationto prevent the failure to occur. Show your solutions to support yourrecommendation.4PSteelBronzeAluminum| P2 ft3 ft2.5 ft

Answered: Image /qna-images/answer/63dad036-a2c3-4daf-8988-1b29712031a6.jpg

Please refer to the figure shown below. IfP is equal to 6,720 lb., and if all the rods have a cross-sectional area to be 0.4 sq. in. Explain why the set-up will fail or will not fail if the allowable stresses in Steel is 120MPA; 90MPa in Alumimun; and 100Mpa in Bronze. As the civil engineer of the project, if the set-up fails, provide a recommendation to prevent the failure to occur. Show your solutions to support your recommendation. 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft

Please refer to the figure shown below. IfP is equal to 6,720 lb., and if all the rods have a cross-sectional area to be 0.4 sq. in. Explain why the set-up will fail or will not fail if the allowable stresses in Steel is 120MPA; 90MPa in Alumimun; and 100Mpa in Bronze. As the civil engineer of the project, if the set-up fails, provide a recommendation to prevent the failure to occur. Show your solutions to support your recommendation. 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

There are two approximate methods for estimation of steel quantities. For schools 1 ton per 15.05 m3 of structure, what is the estimation for a lintel of span 1500mm?
Engineering Economics 05 Please find the cost per unit if steel is used? Thankyou po
In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in the cables are tightened until the stress in the cables reaches 60000psi. If the working compressive stress for the wood is 216psi. Determine the smallest permissible diameter of the pole.___________inches in 2 decimal places. Take note: Write it on a paper, hand written showing answer. Thanks
Given the class averages: F = 4.9 N, W= 0.0098 m, t= 0.0098 m, d =29 intervals (dial gauge reading) and L = 0.3 m Calculate the stiffness, in GPa, for the steel. (give your answer up to three significant figures).
The maximum force in each rod can not exceed 1380 NN . Part A Determine the greatest mass of the crate that can be supported. (Figure 1) Express your answer to three significant figures and include the appropriate units.
The assembly consists of a 20-in. wooden dowel rod and a tight-fitting steel collar. Determine the distance x̄ to its center of gravity if the specific weights of the materials are γw = 150 lb/ft3 and γst = 490 lb/ft3. The radii of thedowel and collar are shown.
please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 0.68 in from the top of the beam on section 1.91 feet to the right of B if P = 1105 lb, Q = 4147 lb, w = 0.76 in, L = 8.2 in, b = 3.76 in, and h = 1.21 in. Round off the final answer to two decimal places.
A floor system in a small building consists of wood plans supported by 50mm (nominal width) joists spaced at a distance of 0.40 m, measured center to center. The span length of each joist is 3.2 m. The uniform load carried is 5.8 kPa which includes the weight of the floor system. (Do not consider reduction of capacity of the beam) What is the cost of timber beams in a 2 meters span of floor (hint: determine how many beams in 2 meters span), , if the price of the timber is Php 65.00 / boardft.?
NEED IN 1 HOUR PLS THANKS!! A surveyor's steel tape is 100 ft long and has a cross-sectional section of 0.250 inch by 0.03 inch. Determine the elongation when the entire tape is stretched and held taut by a force of 12 lb. The modulus of elasticity is 30 x 10⁶ lb/in².
Refer to the beam loaded as shown. What is the value of Ay?
A wooden joist 15 cm deep by 7.5 cm wide is reinforced by gluing to its lower face a steel strip 7.5 cm wide by 0.3 cm thick. The joist is simply-supported over a span of 3 m and carries a uniformly distributed load of 5000 N. Find the maximum direct stresses in the wood and steel and the maximum shearing stress in the glue. Take Es/Et = 20. (Cambridge) Answer: wood 4.56 MN/m2; steel 52.9 MN/m2; glue 0.21 MN/m2. Show your solution
Could you help with the reaction forces? Dy, Ay, Ax, Dx ? thanks