Shear & bending moment at 3 ft and at 8 ft from the left end of the beamb)Find Reactions RA and RBFind: a)Draw the Load DiagramDraw the Shear Diagram, Find Vmax, V=0 at x =?,Draw the Moment Diagram, Find Mmax15 kips6-0" 6'-0".0-.2

Find: a) b) c) Shear & bending moment at 3 ft and at 8 ft from the left end of the beam Find Reactions RA and RB Draw the Load Diagram Draw the Shear Diagram, Find Vmax, V 0 at x =?, Draw the Moment Diagram, Find Mmax e) 15 kips I kip/t B 6-0" 6-0" 12-0"

Find: a) b) c) Shear & bending moment at 3 ft and at 8 ft from the left end of the beam Find Reactions RA and RB Draw the Load Diagram Draw the Shear Diagram, Find Vmax, V 0 at x =?, Draw the Moment Diagram, Find Mmax e) 15 kips I kip/t B 6-0" 6-0" 12-0"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A symmetrical parabolic curve passes through point A whose elevation is 23.23m at a distance of 54…

Q: 1400

A: Given:- f'c = 32 MPa, Ec = 30,100 MPa, and fsy = 500 MPa To find:- a) Calculate the value of Mu for…

Q: A metal ball of radius 90 centimeters is coated with a uniformly thick layer of ice, which is…

Q: MOMENT AREA METHOD FIND THE SLOPE AT POINTS B & C E= 200GPA I= 360x106mm4 5m 10KN A 10m

A: Moment Area Method: Given: E = 200GPa=2 x 105 N/mm2 I = 360 x 106 mm4 EI = 7.20x1013 N mm2

Q: The specified 28-day compressive strength of concrete for a project is fc’ = 36MPa. This statistical…

Q: Air at 27°C and standard atmospheric pressure flows through a furnace filter with an average…

Q: SITUATION: A rectangular channel conveying water enters a transition region. The depth of flow in…

A: Given data in question Rectangular channel Depth before and after jump To find out Head loss

Q: A clay sample originally 25 mm thick at a void ratio of 1.120 was subjected to a compressive load.…

A: Given data in question Initial height Final height Initial void ratio To find out Final void ratio

Q: n of reinforcement concrete structure exposed to seawater, the minimum specified compressive…

A: According to ACI-318 :fcr=max{f'c+1.34sf'c+2.33s-3.45f'c=compressive dtrengths=standrd deviation for…

Q: For a roof truss system of an industrial building, following data is given Span of truss = 6m…

Q: There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 ×…

Q: QUESTION 2 In an experimental set-up to measure the shock losses due to sudden expansion, the…

Q: Find Potontial eneryy mls

Q: A composite beam is constructed using a steel plate (14 mm x 125 mm) with two wood beams (75 mm x…

Q: An equilateral triangulated 2D truss as shown below is subjected to a load 20 kN at B. The force (in…

Q: Assume that P = 13 kips and L = 5 ft. Determine the reaction force at C. Assume that El is constant…

Q: = 40 MN/m2, 80 MN/m?. What are the principal For a case of plane stress, o, = o, = 0, ty = stresses…

Q: A 220 kg wooden raft floats on Lake Sebu and when Boss Junlie who weighs 75 kg stands on the raft,…

Q: A W24x250 is used as a beam to support a concrete slab floor system with a one-way traffic pattern.…

A: FY = 248MPa

Q: Show an illustrative example of a case where there is conflict between written specifications and…

Q: A commercial building is located 7 m from the centerline of the inside lane of a curve section of a…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: The beam shown in the given figure has a desian bending moment value of 4 kN 4 kN-m 2 kN-m A + 0.5 m…

Q: SITUATION: A liquid limit test conducted on a soil sample in the cup device gave the laboratory…

A: To find liquid limit

Q: What is the amount of moisture to be removed from a material whose moisture content is 14% with dry…

Q: In a framed connection an l.S.L.B. 350 @ 485.6 N/m transmits an end reaction of 150 kN and a moment…

Q: A rigid pavement is to be design for a wheel load of 50kN. If the tensile strength of the concrete…

A: Given, Wheel load (W) =50 kN or 50,000 N f'c = 21 MPa Tensile strength (σ) = 0.7 f'c

Q: 8. Assuming vehicles arrive following a Poisson distribution, it implies that their headways are…

A: 8. Answer:(B) false

Q: 12. Calculate the equivalent radius (cm) of the resisting section of 20 cm slab, if the ratio of…

A: given- slab thicknes h=20 cmratio=radius of wheel load distribution athickness of the slab h=2

Q: A square tied column 400 mm by 400 mm is reinforced with 8-20mm diameter bars with fy = 410 MPa.…

Q: For the given cross-section, determine the following section properties: (a) Location of the…

A: Given data:

Q: The initial principal stresses at a certain depth in a clay soil are 100 kPa on the horizontal plane…

Q: 4. What is cavity ratio (CR)? How to solve it? 5. What are effective cavity reflectances? How to…

A: Cavity Ratio (CR)- It is the number that is computed by using the distance from the plane of the…

Q: Consider a farm irrigation ditch in a loam soil having the following dimensions: bottom width, 0.5m;…

A: Bottom width = 0.5m Total depth = 0.6m Side slope 1H:1V means slope m= 1 tan450=1 Depth of…

Q: A plate is connected to another plate via 20 mm diameter rivets. It carries a load of P=155 kN at a…

Q: Question 6- Slab Design The stability of the following needs to be checked. Design the wall based on…

A: Factor of Safety against Sliding: It is defined as the ratio of forces which prevent the sliding…

Q: principal stresses at a certain depth in a clay soil are 100 kPa on the horizontal plane and 50 kPa…

Q: Given the tabulated measurement of a closed traverse with unknown length and azimuth of line DE,…

Q: OThe grading works of a proposed national road shows the following data. FHD= 50 m LEH= 450 m Cost…

Q: 2. If P = 200 kN, determine the maximum live load that the connection could carry based on %3D…

Q: A 1.5m square tank contains water to a depth of 2.6 m. A cubical block of wood, 0.6 m on each side,…

Q: A commercial building is located 7 m from the centerline of the inside lane of a curve section of a…

A: Distance from center line of cure (Mv) = 7 m Radius of curve (R) = 110 m Perception time (t) = 2…

Q: If the travel time delay on a signalized intersection approach is 10 sec/veh, the stopped time delay…

Q: No. 2. For the cantilever beam and loading shown, plot shear and bending moment diagrams and then…

A: Intensity of UVL = 90 kN/m intensity of point load = 70 kN Total span of beam = 4.5 m

Q: The maximum allowable rate of crashes at intersections is 9 per million entering vehicles. At an…

Q: A clay specimen was tested in a laboratory consolidation device, which was 12.7 mm (½ in.) thick and…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: The horizontal force P = 67 N is applied to the upper block with the system initially stationary.…

Q: Which of the following is a warning sign (traffic): Sharp Turn sign Stop Sign Two-Way sign Give Way…

A: warning sign is used to indicate hazardous conditions which are not visible to the driver…

Q: Energy line

A: flow takes from A to B BECAUSE energy at A is more than B and we know that flow takes from high…

Q: Calculate the specific weight, density and specific gravity of 1 litre of petrol which weighs 7 N.

A: Given data, Weight of petrol = 7 N Volume of petrol = 1 litre To find out the specific weight,…

Q: The soil profile for a future building construction site is shown in the following figure. The…

Question

Shear & bending moment at 3 ft and at 8 ft from the left end of the beam
b)
Find Reactions RA and RB
Find: a)
Draw the Load Diagram
Draw the Shear Diagram, Find Vmax, V=0 at x =?,
Draw the Moment Diagram, Find Mmax
15 kips
6-0" 6'-0"
.0-.2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Statics Review. Make sure to draw FBD(s). Given the beam with loading as shown below: A 2 kN/m ILITI PE 5m B f 5m Find: (a) The reactions at A and D (b) The internal shear force at C (c) The internal moment at C 20kN E 5m с + 5m D UMI
Two d mm*10 mm cover plates are welded to two UPN 200 channels 100 mm high to form the cross section of the compound beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 19.10*106 mm4. a) Determine the support reactions. b) Draw the shear force and bending moment diagrams. c) If the allowable bending stress of the beam is 300 MPa, find the required width d of the plates to safely support the load.
Identify the maximum shear and maximum moment. Answers: Vmax = 28.98 kN, Mmax = -85.25 kN-m. Kindly give me the solution of this please.
A simple beam AB supports two connectedwheel loads 3P and 2P that are a distance d apart (seefigure). The wheels may be placed at any distancex from the left-hand support of the beam. (AssumeP =12 kN, d = 2 m, and L =15 m.)(a) Determine the distance x that will produce themaximum shear force in the beam, and alsodetermine the maximum shear force Vmax.(b) Determine the distance x that will produce themaximum bending moment in the beam, andalso draw the corresponding bending-momentdiagram.
For the beams loaded as shown, do the following: 1. determine the support reactions; 2. determine the maximum shear by the Area-Method; 3. draw the shear diagram of the beams; 4. determine the maximum moment and its location by the Area-Method; 5. draw the moment diagram of the beams; 6. draw the elastic curve; 7. determine the moment at 4.5m of Beam B by Area-Method; 8. determine the moment at 2.5m of Beam A by Area-Method. Please encircle your answers.
(a) Determine the reactions at the supports and draw the bending moment diagram for the following structures. (b) Redo problem (a) by using the bending moments over support A and B as the redundant forces. (c) Repeat problem (a) if there are support settlements of 8mm, 5mm and 2mm at A, B and C respectively. Given E=200GPa, I=107mm4 .
Using method of sections, determine the reaction at A, the force in members BD, FE and CE if θ=30degrees, Φ=60degrees and d=12ft.
The beam is used to support a dead load of 400 lb/ft, a live load of 2 k/ft, and a concentrated live load of 8 k. Determine the maximum positive shear just to the right of the support at A. Assume A is a roller, C is fixed, and B is pinned.
The shown in the figure is to be analyzed using cantilever method. Which of the following: 1. most nearly gives the axial force in member DE? A. 22.50 kN B. 37.50 kN C. 30.00 kN D. 7.50 kN 2. most nearly gives the moment at A? A. 150 kNm B. 30 kNm C. 120 kNm D. 90 kNm 3. most nearly gives the shear on member BE? A. 20.00 kN B. 10.00 kN C. 7.50 kN D. Other:_____
A continuous beam is supported by a spring at D with spring constant of 40kN/m as shown. Determine the reactions at the supports A and B and the spring force and draw the bending moment diagram. Given E=200GPa, I=4×107mm4 . (Hint : take the spring force as unknown).
Subject: Structural Analysis Instruction: Using Three Moment Equation, find the reactions at the support. Neglect sidesway.
Determine the shear force V in the beam at a point located 1.60 m to the right of point B. The ground reactions are provided.Ay = 65.60 kNCy = 58.40 kN