Po Air R-22 FIGURE P4.31 4.31 A vertical cylinder (Fig. P4.31) has a 90-kg piston locked with a pin trapping 10 L of R-22 at 10°C, 90% quality inside. Atmospheric pressure is 100 kPa, and the cylinder cross-sectional area is 0.006 m². The pin is removed, allowing the piston Pin to move and come to rest with a final temperature of 10°C for the R-22. Find the fi- nal pressure, final volume, and work done by the R-22.

Po Air R-22 FIGURE P4.31 4.31 A vertical cylinder (Fig. P4.31) has a 90-kg piston locked with a pin trapping 10 L of R-22 at 10°C, 90% quality inside. Atmospheric pressure is 100 kPa, and the cylinder cross-sectional area is 0.006 m². The pin is removed, allowing the piston Pin to move and come to rest with a final temperature of 10°C for the R-22. Find the fi- nal pressure, final volume, and work done by the R-22.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a three-stage compressor, the pressure ratio in each stage is equal and its value is 1.3, the first inlet temperature to stage 300K, outlet pressure from first stage 1000mmHg, , Polytropic yield 0.92. m C1 C2 = C2s C3 C3s = 500 "It s Isentropic exponent=1.4, coefficient of heating heat under constant pressure= 1005 kgK' your mercury density= 13550 and gravitational acceleration= 9.81 m3 m3 a) Find the actual and isentropic temperature of the exit from the 1st stage. b) Find the actual and isentropic temperatures of the exit temperatures from the 2nd stage. c) Find the real and isentropic work consumed in Stage 2. d) Put the available data and your calculations in the compressor (h-s) diagram.
Air, 5.37 kg, is compressed in a piston‑cylinder device from 91.3 kPa and 65.3 ∘C to 195.2 kPa in an isothermal process. Assume the air behaves as an ideal gas. Given: Cp=3.5R constant, MW=29 g/mol, and Tsurr=23.6 ∘C What is the heat interaction (in units of kJ)? What is the lost work (in units of kJ)?
104#1. an ideal gas with R=0.062 BTU/lbm-degree R and Cv=0.158 BTU/lbm-degree R undergoes athree process cycle in a cklose system. from the initial state of 20 psia and 570degree R, the gas is compressed at coinstant pressure to 1/5 of its initial volume, process 1-2; it is then heated isochrocally to state 3, process 2-3; and finally, it expands polytopically with index n=1.5 back to its initial state, process 3-1. determine the pressure, specific volumes and temperatures at cardinal points around the cycle and the cycle thermal efficiency.
There's a copper calorimeter container with the mass 0.2 kg and has 0.32 kg of H2O and also 0.036 kg of ice (thermal equilibrium at atm). If we drop 1.5 kg of lead at a temperature of 200 Celsius into calorimeter container, find the final temperature (in Celsius). Please show work Lead=131J/kgK Copper=390J/kg.K H2O = Cw = 4190 J/kg.K & LF = 3.34 x 105 J/kg
A perfect gas has a value of R = 58.8 ft-lbf per lbm per unit degree Rankine and k = 1.26. If 20 BTU are added to 5 lbm of this gas at constant volume when the initial temperature is 90 ⁰F. Find the following: (a) T₂, (b) ∆H, (c) ∆S, (d) ∆U, (e) Wn
A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V1= 1.00 m3, the pressure is p1= 400.00 kPa, the temperature is T1= 300.00 K. An electric heater within the device is turned on for a time of Δt = 5.00 min. The current is I = 3.00 A, and the source voltage is V = 120.00 V. During the heating process, the gas expands, and a heat loss of Qout = 2.80 kJ occurs. The gas constant is R = 0.297 kPa·m3/(kg·K), and the room temperature specific heat at constant pressure is cp =1.039 kJ/(kg·K). Calculate the mass of the gas, m__________ (kg)
A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V1= 1.00 m3, the pressure is p1= 400.00 kPa, the temperature is T1= 300.00 K. An electric heater within the device is turned on for a time of Δt = 5.00 min. The current is I = 3.00 A, and the source voltage is V = 120.00 V. During the heating process, the gas expands, and a heat loss of Qout = 2.80 kJ occurs. The gas constant is R = 0.297 kPa·m3/(kg·K), and the room temperature specific heat at constant pressure is cp =1.039 kJ/(kg·K). Calculate the electrical work done on the gas, Wele__________ (kJ)
4. Use the thermodynamic tables and show your work please.
Thermodynamics: Please show how to solve this step by step and what is the answer to the certain probldm
Two pounds of gas, R= 26 ft-lb /lb-R and k=1.10, undergo a polytropic from 15 psia, 100 F to 75 psia, 3.72 ft0. Determine the value of “n”, ΔH, ΔS, Q and Work.
A tank contains Helium for which R = 382 ft.lbf/lb.-R and k = 1.66, is heated from 85°Fto a final temperature of 190°F in an unknown process. Find the value of cpA. 1.235 Btu/lb-R B. 1.335 Btu/lb-R C. 1.435 Btu/lb-R D. 1.535 Btu/lb-R
An ideal gas fills a piston-cylinder device, being initially at a certain state 1, with known pressure P1 and specific volume v1. The piston is then pushed downwards, compressing the gas inside the cylinder isothermally and reversibly, until a pressure P2 is achieved. Assume: kinetic, potential, and any other form of energy being zero, except internal thermal energy; no energy generation/depletion inside the domain; constant specific heat, and, known gas constant R. Determine the change in specific entropy undergone by the gas, in terms of P1, P2, and R. Also, show the process in a T-s diagram indicating initial and final states