11:05 C d ļ G A O图“ぐRitesh Sah...MoreEdit1.Point charges ql and q2 are held in place at the(x,y) coordinates specified below. Point P is apoint of interest, there is no charge at point P.Charge q1 +2.778e-9 Cat (1,1) meters.Charge q2 = +1.00e-9 Cat (5,1) meters.Point P is at (5,4) meters.Charges q1 and q2 on an xyplane.Use the methods shown in class to:• Calculate the magnitude/size of the electric field at point P due to chargesq1 and q2.• Calculate the Trig Angle, measured counter-clockwise from the +x-axis indegrees, of the electric field at point P due to charges q1 and q2.

Given q1 =2.778 nC q2 = 1nC 1) To find electric field at point P 2) To find angle of resultant…

Answered: Point charges q1 and q2 are held in…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter3: Magnetic Starters

Section: Chapter Questions

Problem 30SQ

See similar textbooks

Similar questions

C. A small wind turbine of blade diameter 185 cm is subjected to upwind velocity of 11.7 m/s and downwind velocity of 9.3 m/s. Calculate the power and energy produced by the turbine per year. Density of wind is 1.25 Kg/m3.
When two identical parallel wires are 3 m apart, the inductance per unit length is 2.5 μH/m. Calculate the diameter of each wire. explain the steps of the problem
A pure element is connected across an AC signal. CH1 and CH2 measures the voltage and current respectively: CH1 (Yellow) Settings: CH2 (Blue) Settings: Volts/Div: 50V Current Probe Ratio: 100 mV/mA Time/Div: 5ms Volts/Div: 20V Probe Settings: X1 Time/Div: 5ms Probe Settings: X1 If ?? (distance between two ‘purple’ cursors) is 5ms, determine:a. CH2 Peak Currentb. CH2 RMS Currentc. Impedance of the pure elementd. Type of load. If reactive, indicate the values of inductance or capacitance
In the circuit below, if the inductance L is large enough to operate in continuous current mode. a) Draw the waveform of the output voltage and mains current for the 45 degree trigger angle when the switch S is in transmission. b) Average value of output DA voltage VDC1 when switch S is open, output DA when switch S is closed (in transmission) If the average value of the voltage is VDC2, calculate the value of VDC1 / VDC2. Lesson: power electronics please quick
A lightning strikes a 30-m unshielded over-head transmission line tower Which has the following parameters Surge impedance of the tower= 100ohms Surge impedance of lightning channel at tower top =500ohms Tower-footing resistance=10ohms Tower height =30 m Cross-arm height=27m The lightning strike current is assumed to be a constant 30 kA for a duration of 20 µs. The traveling wave propagation speed in the tower is 1.2* 108 m/s. a)draw the voltage lattice diagram with proper labels of the time b) ignoring the phase voltage, determine the insulator voltage after 2µs. c) The insulator voltage approaches a constant value after 2 µs. If the basic impulse insulation level (BlL) of the insulator for phase conductor is 150 kV, evaluate the condition of the insulator and conclude the type of power quality problem that will occur for an end-user facility connected to the transmission line. Assume that the surge arresters and circuit breakers at the end-User facility are working properly.
A lossy dielectric piece of food with a dielectric constant of 40 and a loss tangent of 0.02 is cooked by the radiation of an electromagnetic wave with an electric field amplitude of 15 V/m and a frequency of 2.4 GHz by a microwave oven. How many Watts/m³ is the average power consumed in the environment per cubic meter?( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE). A)4 B)12 C)8 D)10 E)16
A voltage e(t) = 100 sin 314 t is applied to a series circuit consisting of 10 ohmsresistance, 0.0318 henry inductance and a capacitance of 63.6 μF. Determine:a. Expression for i(t)b. Phase angle between voltage and currentc. Power factord. Active power consumede. Peak value of pulsating energy
A battery is connected in series with a small generator to supply a purely resistive load of 5 ohms. The expression of the total voltage is e =24 + 60 sin 377t Volts. Determine the expression for the current and its RMS value. a. i = 5.8 + 12sin 377t, 9.75A b. i = 4.8sin 377t, 9.75A c. i = 12sin 377t, 9.75A d. i = 4.8 + 12sin 377t, 9.75A
When two identical parallel wires are 3 m apart, the inductance per unit length is 2.5 μH/m. Calculate the diameter of each wire.explain the steps. answer: 11.58 mm use the parallel wires formula
Which of the following statements correctly describe the representation of power in an AC system using a power triangle? Select one: A. Capacitive reactive power is represented vertically upward on the power triangle. B. Inductive reactive power is represented horizontally on the power triangle. C. The apparent power (Pa) is not represented on the power triangle. D. Working power (P) is represented vertically upward on the power triangle
Outer radius r2 = 50 cm, puncture of air in a concentric spherical electrode system resistance is Ed = 30 kV/cm, applied voltage is 200 kV. Draw the perforation curve of the system. Calculate the inner radii of the two patterns corresponding to 200 kV on the perforation curve. Indicate the discharge sites.
Calculate the 50 Hz inductive reactance at 1 m spacing in ohms/km of a cable consisting of 12 equal strands around a non conducting core. The diameter of each strand is 0.25 cm and the outside diameter of the cable is 1.25 cm.

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS