Prob 02: The two rods are used to support a crate with weight of 2kN. The rod are made of the same material and of the same diameter. If the failure tensile normal stress for this material is 200 mPa, what is the minimum required diameter for the rods in mm? (2 points) 45° 30°

Prob 02: The two rods are used to support a crate with weight of 2kN. The rod are made of the same material and of the same diameter. If the failure tensile normal stress for this material is 200 mPa, what is the minimum required diameter for the rods in mm? (2 points) 45° 30°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The thin-walled vessel shown is fabricated by joining two cylinders with thickness 26 mm using 20…

A: Given values are: Thickness of the vessel, t= 26mm Number of bolts= 20 Diameter of bolts= 20mm Outer…

Q: A leaf spring is made of plates 50 mm wide and 8 mm thick. The spring has a span of 700 mm.…

Q: H.W A rigid slab weighing 600 Kw is Placed uron two bronze vads and one Steel Vocd Cnch of bo00 mm?…

A: Given:-m = 600 kN=600*1000 NArea of two bronze rods = Area of one steel rod = 6000mm2T = 15 degree…

Q: A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that…

A: Given data- load P=1960 Nstress σ=100 N/mm2

Q: a) A holiow steel tube used in a roof structure has an outer diameter, d; = 104 mm and inner…

Q: 1.) A STEEL WIRE 30 ft LONG HANGING VERTICALLY SUPPORTS A LOAD OF 500 lb. 30 ft NEGLECTING THE…

Q: A bolt is under an axial thrust of 9.6 kN together with a transverse force of 4.8 kN. If factor of…

Q: A leaf spring is made of plates 50 mm wide and 8 mm thick. The spring has a span of 700 mm.…

A: For leaf spring M=WL4we knowFor all platesM=M'×nM'=σIy=σbt312t2M=σbt26×n=WL4n=32WLbt2σ(number of…

Q: 4. A cylindrical steel pressure vessel S*100 mm in diameter with a wall thickness of 10 mm, is…

A: GivenDiameter, D=2500mmThickness, t=10mmp=5 MNm2Tangentail Stress, σt=?Longitudinal Stress, σl=?

Q: A 1 meter long steel rod AB of 15-mm diameter is held snugly (without any initial stresses) between…

Q: Current Attempt in Progress A hollow aluminum rod (1) is connected to a hollow bronze rod (2) at…

Q: es Refer the beam shown with cross section of thickness, t = 15 mm. If F = 84 kN and a = 150 mm, F…

Q: Situation #3: A steel wire 12m long, hanging vertically supports a tensile load of 2 kN. Determine…

A: Length of steel wire (L) = 12m Vertically supports a load of (P) = 2kN = 2000N Stress = 140Mpa = 140…

Q: 2 A leaf spring is made of plates 50 mm wide and 8 mm thick. The spring has a span of 700 mm.…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: RSITY -100 mm -H Example 1 A hollow steel tube with an inside diameter of 100 mm must carry a…

A: Solution Given Data Inside Dia Di= 100 mm Tensile Load P =400 KN Limited Stress σ= 120 MN/m2

Q: The tank shown is fabricated from steel plate. Determine the minimum thickness of the plate which…

A: Given:- The dimension of the tank = 500 mm × 1000 mm The stress is limited to the value = 40 MN/m2…

Q: f the shaft?A

A: We knowμ=Lateral strainLongitudinal strainLateral strain=δddLongitudinal strain=δLL

Q: rind the minimum diameter of a steel wire, which is used to raise a load of 4000 N if the stress in…

A: Given data : Load (P)=4000 NStress (σ)=95 MN/m2Stress is defined as the force per unit area . Stress…

Q: A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If…

Q: A closely coiled helical spring of mean diameter 140 mm is made up of 12 mm diameter steel wire.…

A: GivenDiameter of helical spring D=140 mmRadius R=70 mmDiameter of steel wire which is used in spring…

Q: Calculate the strain if initial length of rod is 104 mm and extension in rod due to tesnile load is…

Q: A solid 11 mm diameter shaft is subjected to an axial load of P-33 kN and a torque of Tacting as…

A: Note: Hi! Thank you for the question as per the honour code, we’ll answer the first question since…

Q: A leaf spring is made of plates 50 mm wide and 8 mm thick. The spring has a span of 700 mm.…

Q: Situation #3: A steel wire 12m long, hanging vertically supports a tensile load of 2 kN. Determine…

Q: A leaf spring is made of plates 50 mm wide and 8 mm thíck. The spring has a span of 700 mm.…

A: We have formulaσmax=32(WLnbl2)δmax=38(WL3nbl3E)

Q: A copper tube is rigidly attached between a steel rod and an aluminum rod as shown in the figure.…

Q: Question 3 A steel column of hollow circular cross section is supported on a circular steel base…

A: To find Thickness t of column Diameter D of base plate

Q: A built-up tee-shape in the figure shown is consists of a 7/8 inch x 10 inch flange and a 1 inch x…

Q: A hollow circular column of internal diameter 20 mm and external diameter 40 mm has a total length…

A: The given data is: The hollow internal diameter=20 mm and external diameter=40 mm E = 2 × 10^5 N/mm2…

Q: An unequal leg angle-iron is loaded as shown in Fig. 9.12. Determine the stress at point B.…

A: Stress at B , σ=MyI As solved in the above image where M= 8 KNM…

Q: An aluminum alloy cylinder (2) is clamped between rigid heads by two steel bolts (1), as shown. The…

A: Determine(a) the normal stress in the aluminum cylinder.(b) the normal strain in the aluminum…

Q: PROBLEM 3 A compound shaft consisting of a 50mm diameter bronze segment and a 75mm diameter aluminum…

Q: The drive shaft AB of an automobile is made of a steel having an allowable shear stress of 8 ksi. If…

Q: A copper tube is rigidly attached between a steel rod and an aluminum rod as shown in the figure.…

A: Given data in question Permissible stresses Loads To find out Area Diameter

Q: 5. The rigid bar is supported by a smooth pin and two rods as shown. Neglect the weight of the rigid…

Q: of 10,000 mm4. Determine the stresses in MPa. Indicate if the stresses are in compre -3 m 3 m- C B…

Q: The gas storage tank is fabricated by bolting together two half cylindrical shells and two…

A: Given data:- Pi=3MPa σtank=150 MPa σbolt=250 MPa Di =4000 mm…

Q: A hollow steel tube used in a roof structure has an outer diameter, d; = 104 mm and inner diameter,…

Q: A steel tube with an Outside diameter of 120 mm must carry a tensile load of 550 KN. Determine: a)…

A: Given data P= 550 kN Do = 120 mm

Q: Q2/ the structure shown below, support from fix at the left , the max normal at bronze =200 MPA,…

Q: 1.) A STEEL WIRE 30 ft LONG HANGING VERTICALLY SUPPORTS A LOAD OF 500 lb. 30 ft NEGLECTING THE…

A: Given,The length of the steel wire,L=30ftLoad is,P=500lbThe elongation is,δ=0.20 inchE=29×106 Psi

Q: A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of…

Q: The drill pipe has an outer diameter of 3 in., a wall thickness of 0.25 in., and a weight of 50…

Q: H.W3: 1- A hallow steel tube 3.5 m long has external diameter of 120 mm. The tube was subjected to…

A: Given data Change in length External diameter Length Load Modulus of Elasticity. According to…

Q: A shaft is made of bronze at length AB and steel at length BC fixed at both ends. It is subjected to…

A: The behavior of the stress component of the shaft because of the torsional moment acting on it is…

Q: Situation #3: A steel wire 12m long, hanging vertically supports a tensile load of 2 kN. Determine…

Q: A 2 m long shaft is transmitting 90 kW at 150 RPM. The allowable shear stress in the material is 60…

Q: 1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in.…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Prob 02: The two rods are used to support a crate with weight of 2kN. The rod are made of the same material and
of the same diameter. If the failure tensile normal stress for this material is 200 mPa, what is the minimum
required diameter for the rods in mm? (2 points)
45°
30°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the point given the plane stress state, which of the following is the correct type and limit values of Mohr Circle? sx =-40 MPa (Bası), sy =60 MPa (Çeki) txy =60MPa
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 265 mm, a wall thickness of 11 mm, and a length of 4.6 m. The pipe supports a compressive load of 640 kN. After the temperature of the pipe drops 35°C, determine:(a) the axial deformation of the pipe.(b) the change in diameter of the pipe.
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 225 mm, a wall thickness of 15 mm, and a length of 5.0 m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 48°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe.
The constructed shaft is composed of a tube AB and a solid bar BC. The tube has an inner diameter of 20 mm and an outer diameter of 28 mm. The bar has a diameter of 12 mm. Determine the average normal stress at points D and E and identify whether the points are in compression or tension.answer:σD = -13.26 Mpa (compression) σE = 70.74 Mpa (traction)
Q4) two plate one lower fixed and one upper moved with a velocity 0.3 m/s , thedistance between the two plate is 0.3 mm and viscosity of the liquid is 0.65*10-3kg/m.s , calculate the shear stress on the upper plate .
A simply supported rectangular beam of length 5m has a width of 300mm and an effective depth of 500mm. The beam is to be reinforced using 12mm bars. The beam supports service dead loads of 25 kN/m and 30 kN/m, respectively. f'c= 28 MPa, fy= 420 MPa 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam. Expert Solution
Determine the average normal stress in each rod if T2=400∘F Calculate the new length of the aluminum segment.
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding.
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Calculate the maximum shear stress with Mohr's circle? d) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion?
Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.8 GPa. Bar (2) is a nylon material that has an elastic modulus of 0.9 GPa. Each bar has a cross-sectional area of 1050 mm2. Using L = 395 mm and Δ = 7.3 mm, what magnitude of load P will cause the normal stress in each bar to be the same value? [Answer: P = 67.0 kN]
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 19 kips, F2 = 33 kips, and the normal stress in each rod must be limited to 29 ksi, determine the minimum diameter d2 required for rod (2).
A steel column of hollow circular cross section is supported on a circular steel base plate and a concrete pedestal . The columm has outside diameter d = 250 mm and supports a load P= 750 kN. (a) If the allowable stress in the column is 55 MPa, what is the minimum required thickness ? Based upon your result, select a thickness for the column. (Select a thickness that is an even integer, such as 10, 12, 14,... in units of millimeters.) (b) If the allowable bearing stress on the concrete pedestal is 11.5 MPa, what is the minimum required diameter D of the base plate if it is designed for the allowable load P that the column with the selected thickness can support?