Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 19 kips, F2 = 33 kips, and the normal stress in each rod must be limited to 29 ksi, determine the minimum diameter d2 required for rod (2). Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 19 kips, F2 = 33 kips, and the normstress in each rod must be limited to 29 ksi, determine the minimum diameter d2 required for rod (2).FA(DF2F2В(2)CO 2.61 in.O 1.45 in.O 1.93 in.O 2.30 in.O 2.06 in.

F1=19Kips F2=33kips To find diameter of rod 2

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 19 kips, F2 = 33 kips, and the normal stress in each rod must be limited to 29 ksi, determine the minimum diameter d2 required for rod (

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 19 kips, F2 = 33 kips, and the normal stress in each rod must be limited to 29 ksi, determine the minimum diameter d2 required for rod (

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Related questions

Q: Determine the state of stress at points K and H on the cross-section of the shaft with diameter of…

A: Diameter of shaft(D)=40 mm Force(P1)=15 kN or 15000 N Force(P2)=18 kN or 18000 N

Q: A 9 (1) (2) B C a L

Q: Strength of Materials Lecture-1 Example 1.2 Rigid bar ABC is supported by a pin at A and axial…

A: Given data: A=540 mm2.

Q: For the shown structure, the failure normal stress of member AB is 120 MPa, and the failure shear…

A: Given :- Failure normal stress of member AB = 120 MPa Failure shear stress of the pin at B = 90 MPa…

Q: L60 kN the B Cross-section of members are 40 mm 60 kN diameter. 6 m - For the given 60 kN F truss,…

Q: The force P = 100 kN is applied to the bracket as shown in the figure. Compute the normal stresses…

A: P=100kN To find normal stress at A and B

Q: Rigid bar BC is supported by aluminum rod (1) and bronze rod (2), as shown in the figure. Aluminum…

A: Given data in question Aluminum permissible stress Beonze permissible stress Distance Area…

Q: Problem #3: The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft (…

Q: he stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 90 MPa and S, =-…

Q: For the beam shown, determine the support reactions and draw the stress diagrams. shear and bending…

Q: A cantilever beam is shown in the figure. The rotated cross-section as shown in the figure is…

A: 1 KN.m= 106 N.mm 1 cm = 10 mm 1 MPa= 1 N/mm2

Q: Determine the maximum stress in the member CD if you know that the distributed load W = 40 kN/m, the…

Q: 5 kN is distributed equally among the three rivets, fi e bearing stress between a plate and a rivet;…

A: Given data Diameter, d=25mm Load, P=75kN Thickness, t=25mm The expression for area is given as…

Q: The solid 1.25-in.-diameter rod shown in Figure is subjected to a uniform axial distributed loading…

A: For 0≤x≤aAt equilibrium∑Fx=0Wa+b-x+P+Q-F=07501248-x+2000+1000-F=0at x=10 inF=5375…

Q: Problem 1: The shaft is hollow from A to B and solid from B to C. Determine the maximum shear stress…

Q: Q.10 Athin cylindrical tube closed at ends is subjected to internal pressure. A torque is also…

Q: The d = 15-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

A: Given -

Q: A uniformly-distributed load w is supported by a structure consisting of rigid bar BDF and three…

A: To find the normal stress in each rod and the deflection at F

Q: Determine the normal stress in rod (1) for the mechanism shown. The diameter of rod (1) is 8 mm, and…

A: P=2300 Na= 120mmb=200 mm and c= 170 mm d=90 mmfor equlibrium∑Fx=Ax-P-Pcos 60°= 0Ax= 3450 N∑Fy=Ay-P…

Q: The same torque is applied to two tubes with identical metal sheets, determine the ratio of…

Q: The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 21 mm…

Q: e bar as it is shown in figure. Find maximum stress at point P. F1 = 2 KN , F2 = 5 KN , Lenght of…

A: L=4m D=2mm To find maximum stress at point P

Q: Problem 8: An aluminium pipe column (6.5- inches outside diameter; 0.250 inches wall thickness)…

A: Given, D=6.5int=0.25inand,d=6.5-2*0.25d=6in

Q: Situation 6: A solid shaft is partially inserted in a hollow shaft where it snuggly fits and is…

Q: The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on…

Q: Question 2) In the system given in the figure, a distributed load of w=36 kN/m acts on the rod AB of…

Q: If P = 8.571 kN, determine the stress in member CE assuming that the area in steel is 24 mm^2.

Q: moment of inertia of the cross-section about the neutral axis (in mm4) c) What is the maximum…

A: a.) Calculate the cross-sectional area of the structural tube A=bd-b-2td-2t Substitute the value in…

Q: For the shaft shown, a. Determine the maximum stress on the shaft and the maximum angle of twist of…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The…

Q: A solid circular shaft of diameter d is subjected to a torque T. the maximum normal stress induced…

A: Given data in question Solid circular shaft Diameter d Torque T To find out Maximum normal stress

Q: The shaft is hollow from A to B and solid from B to C. The shaft has an outer diameter of 80 mm, and…

A: Given: The outer diameter of the shaft is 80 mm. The thickness of the wall is 10 mm. The shear…

Q: Three rods joinfly support a 9kN load. Assuming that there was no stress in the rods before the load…

A: given- three rods carrying a total load of 9kn required- to find stress in each rod.

Q: iameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the…

Q: 1.1 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that…

Q: Q The cantilever beam shown in Figure below is subjected to a concentrated load of P. The…

A: Step 1

Q: A solid compound shaft consists of segment (1), which has a diameter of 40 mm, and segment (2),…

Q: principal stresses. The strains measured in these ratio u = 0.3. Determine the magnitude of the…

Q: The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tdircle/…

Q: c. If the allowable stress in rod CD is 125 MPa, what weight W can be safely applied? 38 mm. 1.8 m…

Q: The beam is made from three boards nailed together as shown. If the moment acting on the cross…

A: Solution- (a) The total beam's centroid distance…

Q: .Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the…

A: For abody to be in equilibrium following conditions have to be considered: Sum of all the forces in…

Q: Q1) In Fig.(1), the shaft is subjected to a reversed load P = (2700 to - 900) N. Find the length…

A: The stress at fillet can be calculated as, σf=MI×y=±P2×375π64×504×502=±12000Pπ×503…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

A: Given: shaft 1 Length Diameter Thickness Torque Shaft 2 Length Diameter Thickness Torque

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 3150 mm2 and an…

A: We will take both cases. In each case we will take allowable stress in one bar and calculate stress…

Q: 2. Rods AB and BC have diameters of 3.50 mm and 5.60 mm, respectively. If the 3 kN force is applied…

Q: A compound shaft consists of segment (1), which has a diameter of 1.9 in., and segment (2), which…

Q: Determine the shear stress in pin A (double shear) and the normal stress in DE. The diameter of pin…

Question

100%

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 19 kips, F₂ = 33 kips, and the normal stress in each rod must be limited to 29 ksi, determine the minimum diameter d₂ required for rod (2).

Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 19 kips, F2 = 33 kips, and the norm
stress in each rod must be limited to 29 ksi, determine the minimum diameter d2 required for rod (2).
F
A
(D
F2
F2
В
(2)
C
O 2.61 in.
O 1.45 in.
O 1.93 in.
O 2.30 in.
O 2.06 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Set P1 = 30 kN and P2 = 16 kN in Part A Determine the force in member AD, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. View Available Hint(s) FAD= SubmitPrevious Answers Incorrect; Try Again; 4 attempts remaining Part B Determine the force in member BC, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. View Available Hint(s) FBC = SubmitPrevious Answers Incorrect; Try Again; 5 attempts remaining Part C Determine the force in member BD, and state if the member is in tension or compression. Express your answer to three…
Determine the x, y, z components of internal loading at a section passing through point B in the pipe assembly. Neglect the weight of the pipe. TakeF1 = {100i - 200j - 300k} N and F2 = {100i + 500j}N.
The two aluminum rods support the vertical load P = 20 kN. Determine reactionssupport.
Determine the displacement at pulley B. The A992 steel shaft has a diameter of 30 mm.
Two 10"-15.3 lb channels are welded together as shown in the figure. Find the moment of area of the upper channel about the horizontal centroidal axis Xo of the entire section.
Determine the x, y, z components of force and moment at point C in the pipe assembly. Neglect the weight of the pipe. Take F1 = {350i - 400j} lb andF2 = {-300j + 150k} lb.
The “Nuremberg scissors” is subjected to a horizontal force of P = 600 N. Determine the stiffness k of the spring for equilibrium when θ = 60°. The spring is unstretched when θ = 15°.
Determine the following : 1. Vertical reaction of hinge at A in pounds, Av 2. Horizontal reaction of hinge at A(lbs), Ah 3.Maximum shear value(lbs) 4. Maximum moment value (lb-ft)
A cantilever beam AB with a circular crosssection and length L = 750 mm supports a loadP = 800 N acting at the free end (see figure). Thebeam is made of steel with an allowable bendingstress of 120 MPa.(a) Determine the required diameter dmin (figurepart a) of the beam, considering the effect of thebeam’s own weight.(b) Repeat part (a) if the beam is hollow with wallthickness t =d /8 (figure part b); compare thecross-sectional areas of the two designs.
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 18 mm and an elastic modulus of E = 77 GPa. The steel rod has a diameter of 24 mm and an elastic modulus of E = 180 GPa. Assume a = 3.5 m, b = 1.8 m, and c = 1.1 m. What is the magnitude of load P that is necessary to displace point A 8 mm to the left?
Three steel rods, each having a cross-sectional area of 500 mm2, are assembled in a symmetrical manner, ass shown in the igure. Assume that steek behaves as a linear elastic material with E= 200 GPa. Determine the deflection of joint A due to a downward force of P= 2MN
GI, GE, and GD of the cage system for the loading condition given in Figure 2 Calculate the rod forces. tensile or tensile rod forces Specify the pressure. P1(kN)=20 P2(kN)=45 L3(m)=7