Prob 2. The cantilever beam below is made of steel (E200 GPa) and must support the distributed load as shown. (A) Draw the V and M diagram and determine location and magnitude of the maximum bending moment. (B) Sketch the stress and strain distribution over the cross section at the point where the maximum momen occurs. (C) Determine the stress at point B. 2 kN/m 20 mm 2m 6m 50 mm

Prob 2. The cantilever beam below is made of steel (E200 GPa) and must support the distributed load as shown. (A) Draw the V and M diagram and determine location and magnitude of the maximum bending moment. (B) Sketch the stress and strain distribution over the cross section at the point where the maximum momen occurs. (C) Determine the stress at point B. 2 kN/m 20 mm 2m 6m 50 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The singular force F will be applied to the beam with a hollow rectangular cross section. Accordingly, the location and value of the maximum normal stress that will occur in the whole beam is given correctly in the following? F =400 N, L1 = 3m, L2 = 2m, h1=48mm, h2 =72mm, b1=10mm, b2=20mm
a) 1. The support reaction forces at the A and C, in terms of P,be careful of the sign. 2. Give the expressions of the shear and moment at an arbitrary poistion x of AB segment, in terms of P and x, be careful of the sign. 3. Give the expressions of the shear and moment at an arbitrary poistion x of BC segment, in terms of P and x, be careful of the sign. b)Given l= 1000 mm, P= 4000 N and l1/l=0.66, calculate the internal shear force and draw the moment diagram
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e� = 55 mmmm and is subjected to the loading shown. Let a� = 200 mmmm , b� = 220 mmmm , c� = 350 mmmm , d� = 250 mmmm , and P� = 3.0 kNkN . Take point A to be at the top of the circular cross-section. As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, Mx��. b) Part B - Moment about the z axis at A Part C - Stress due to the normal force To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the normal force. Part D - Stress due to the bending moment about the x axis To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the bending moment about the x axis.
The simply supported joist is used in the construction of a floor for a building. In order to keep the floor low with respect to the sill beams C and D, the ends of the joists are notched as shown. If the allowable shear stress is tallow = 350 psi and the allowable bending stress is sallow = 1500 psi, determine the height h that will cause the beam to reach both allowable stresses at the same time. Also, what load P causes this to happen? Neglect the stressconcentration at the notch.
5.86 The cast iron inverted T-section supports two concentrated loads of magnitude P. The working stresses are 48 MPa in tension, 140 MPa in compression, and 30 MPa in shear. (a) Show that the neutral axis of the cross section is located at d ¼ 48:75 mm and that the moment of inertia of the cross-sectional area about this axis is I ¼ 11:918 106 mm4. (b) Find the maximum allowable value of P.
In a 2.5 cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the section modulus and The base and height of the beam if the base is 75% of its height mm.
A shaft is made of a polymer having an elliptical cross section. If it resists an internal moment of M = 50 N # m, determine the maximum bending stress in the material (a) using the flexure formula, where Iz = 1 4 p(0.08 m)(0.04 m)3, (b) using integration. Sketch a three-dimensional view of the stress distribution acting over the cross-sectional area. Here Ix = 1 4 p(0.08 m)(0.04 m)3.
A beam is subjected to equal 19.1 kip-ft bending moments. Assume ty = t2 = ty= 1 in., d = 10 in, by= 4 in., and b2 = 7 in. The cross- sectional dimensions of the beam are illustrated. Determine; (a) the distance y to the centroid (measured from the bottom), the moment of inertia & about the z axis, and the controlling section modulus S, about the z axis. (b) the bending stress O, at point H (positive if tension, negative if compression). (c) the bending stress y at point K (positive if tension, negative if compression). (d) the maximum bending stress, Omax produced in the cross section (positive if tension, negative if compression).
If the beam has a rectangular cross-section, then the shear-stress distribution will be parabolic. True or False?
If the internal moment acting on the cross-section is 800 N.m, determine the maximum tensile and compressive bending stresses acting in the beam. Sketch the stress-distribution acting on the cross-section.
A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 70 GPa] bar, as shown. The beam is subjectedto a bending moment of 2140 N-m acting about the z axis. Assume b=44 mm, d =50 mm, d =10 mm. Determine:(a) the maximum bending stresses , in the brass plates and the aluminum bar.(b) the stress in the brass at the joints where the two materials are bonded together.
If P = 3 kN, determine the bending stress at points A, B, and C of the cross section at section a–a. Using these results, sketch the stress distribution on section a–a.